Allow PSRAM (SPI RAM) to be used for JSON buffer

wled00/FX_2Dfcn.cpp

@@ -91,12 +91,12 @@ void WS2812FX::setUpMatrix() {
         DEBUG_PRINT(F("Reading LED gap from "));
         DEBUG_PRINTLN(fileName);
         // read the array into global JSON buffer
-        if (readObjectFromFile(fileName, nullptr, &doc)) {
+        if (readObjectFromFile(fileName, nullptr, pDoc)) {
           // the array is similar to ledmap, except it has only 3 values:
           // -1 ... missing pixel (do not increase pixel count)
           //  0 ... inactive pixel (it does count, but should be mapped out (-1))
           //  1 ... active pixel (it will count and will be mapped)
-          JsonArray map = doc.as<JsonArray>();
+          JsonArray map = pDoc->as<JsonArray>();
           gapSize = map.size();
           if (!map.isNull() && gapSize >= matrixSize) { // not an empty map
             gapTable = new int8_t[gapSize];

wled00/FX_fcn.cpp

@@ -1666,7 +1666,7 @@ bool WS2812FX::deserializeMap(uint8_t n) {
 
   if (!isFile || !requestJSONBufferLock(7)) return false; // this will trigger setUpMatrix() when called from wled.cpp
 
-  if (!readObjectFromFile(fileName, nullptr, &doc)) {
+  if (!readObjectFromFile(fileName, nullptr, pDoc)) {
     DEBUG_PRINT(F("ERROR Invalid ledmap in ")); DEBUG_PRINTLN(fileName);
     releaseJSONBufferLock();
     return false; // if file does not load properly then exit
@@ -1676,7 +1676,8 @@ bool WS2812FX::deserializeMap(uint8_t n) {
 
   if (customMappingTable == nullptr) customMappingTable = new uint16_t[getLengthTotal()];
 
-  JsonArray map = doc[F("map")];
+  JsonObject root = pDoc->as<JsonObject>();
+  JsonArray map = root[F("map")];
   if (!map.isNull() && map.size()) {  // not an empty map
     customMappingSize = min((unsigned)map.size(), (unsigned)getLengthTotal());
     for (unsigned i=0; i<customMappingSize; i++) customMappingTable[i] = (uint16_t) (map[i]<0 ? 0xFFFFU : map[i]);

wled00/cfg.cpp

@@ -609,7 +609,7 @@ void deserializeConfigFromFS() {
 
   DEBUG_PRINTLN(F("Reading settings from /cfg.json..."));
 
-  success = readObjectFromFile("/cfg.json", nullptr, &doc);
+  success = readObjectFromFile("/cfg.json", nullptr, pDoc);
   if (!success) { // if file does not exist, optionally try reading from EEPROM and then save defaults to FS
     releaseJSONBufferLock();
     #ifdef WLED_ADD_EEPROM_SUPPORT
@@ -630,7 +630,8 @@ void deserializeConfigFromFS() {
 
   // NOTE: This routine deserializes *and* applies the configuration
   //       Therefore, must also initialize ethernet from this function
-  bool needsSave = deserializeConfig(doc.as<JsonObject>(), true);
+  JsonObject root = pDoc->as<JsonObject>();
+  bool needsSave = deserializeConfig(root, true);
   releaseJSONBufferLock();
 
   if (needsSave) serializeConfig(); // usermods required new parameters
@@ -643,19 +644,21 @@ void serializeConfig() {
 
   if (!requestJSONBufferLock(2)) return;
 
-  JsonArray rev = doc.createNestedArray("rev");
+  JsonObject root = pDoc->to<JsonObject>();
+
+  JsonArray rev = root.createNestedArray("rev");
   rev.add(1); //major settings revision
   rev.add(0); //minor settings revision
 
-  doc[F("vid")] = VERSION;
+  root[F("vid")] = VERSION;
 
-  JsonObject id = doc.createNestedObject("id");
+  JsonObject id = root.createNestedObject("id");
   id[F("mdns")] = cmDNS;
   id[F("name")] = serverDescription;
   id[F("inv")] = alexaInvocationName;
   id[F("sui")] = simplifiedUI;
 
-  JsonObject nw = doc.createNestedObject("nw");
+  JsonObject nw = root.createNestedObject("nw");
 #ifndef WLED_DISABLE_ESPNOW
   nw[F("espnow")] = enableESPNow;
   nw[F("linked_remote")] = linked_remote;
@@ -677,7 +680,7 @@ void serializeConfig() {
     nw_ins_0_sn.add(staticSubnet[i]);
   }
 
-  JsonObject ap = doc.createNestedObject("ap");
+  JsonObject ap = root.createNestedObject("ap");
   ap[F("ssid")] = apSSID;
   ap[F("pskl")] = strlen(apPass);
   ap[F("chan")] = apChannel;
@@ -690,12 +693,12 @@ void serializeConfig() {
   ap_ip.add(2);
   ap_ip.add(1);
 
-  JsonObject wifi = doc.createNestedObject("wifi");
+  JsonObject wifi = root.createNestedObject("wifi");
   wifi[F("sleep")] = !noWifiSleep;
   wifi[F("phy")] = (int)force802_3g;
 
   #ifdef WLED_USE_ETHERNET
-  JsonObject ethernet = doc.createNestedObject("eth");
+  JsonObject ethernet = root.createNestedObject("eth");
   ethernet["type"] = ethernetType;
   if (ethernetType != WLED_ETH_NONE && ethernetType < WLED_NUM_ETH_TYPES) {
     JsonArray pins = ethernet.createNestedArray("pin");
@@ -718,7 +721,7 @@ void serializeConfig() {
   }
   #endif
 
-  JsonObject hw = doc.createNestedObject("hw");
+  JsonObject hw = root.createNestedObject("hw");
 
   JsonObject hw_led = hw.createNestedObject("led");
   hw_led[F("total")] = strip.getLengthTotal(); //provided for compatibility on downgrade and per-output ABL
@@ -830,7 +833,7 @@ void serializeConfig() {
   //JsonObject hw_status = hw.createNestedObject("status");
   //hw_status["pin"] = -1;
 
-  JsonObject light = doc.createNestedObject(F("light"));
+  JsonObject light = root.createNestedObject(F("light"));
   light[F("scale-bri")] = briMultiplier;
   light[F("pal-mode")] = strip.paletteBlend;
   light[F("aseg")] = autoSegments;
@@ -853,12 +856,12 @@ void serializeConfig() {
   light_nl[F("tbri")] = nightlightTargetBri;
   light_nl["macro"] = macroNl;
 
-  JsonObject def = doc.createNestedObject("def");
+  JsonObject def = root.createNestedObject("def");
   def["ps"] = bootPreset;
   def["on"] = turnOnAtBoot;
   def["bri"] = briS;
 
-  JsonObject interfaces = doc.createNestedObject("if");
+  JsonObject interfaces = root.createNestedObject("if");
 
   JsonObject if_sync = interfaces.createNestedObject("sync");
   if_sync[F("port0")] = udpPort;
@@ -961,7 +964,7 @@ void serializeConfig() {
   if_ntp[F("ln")] = longitude;
   if_ntp[F("lt")] = latitude;
 
-  JsonObject ol = doc.createNestedObject("ol");
+  JsonObject ol = root.createNestedObject("ol");
   ol[F("clock")] = overlayCurrent;
   ol[F("cntdwn")] = countdownMode;
 
@@ -971,7 +974,7 @@ void serializeConfig() {
   ol[F("o5m")] = analogClock5MinuteMarks;
   ol[F("osec")] = analogClockSecondsTrail;
 
-  JsonObject timers = doc.createNestedObject(F("timers"));
+  JsonObject timers = root.createNestedObject(F("timers"));
 
   JsonObject cntdwn = timers.createNestedObject(F("cntdwn"));
   JsonArray goal = cntdwn.createNestedArray(F("goal"));
@@ -999,14 +1002,14 @@ void serializeConfig() {
     }
   }
 
-  JsonObject ota = doc.createNestedObject("ota");
+  JsonObject ota = root.createNestedObject("ota");
   ota[F("lock")] = otaLock;
   ota[F("lock-wifi")] = wifiLock;
   ota[F("pskl")] = strlen(otaPass);
   ota[F("aota")] = aOtaEnabled;
 
   #ifdef WLED_ENABLE_DMX
-  JsonObject dmx = doc.createNestedObject("dmx");
+  JsonObject dmx = root.createNestedObject("dmx");
   dmx[F("chan")] = DMXChannels;
   dmx[F("gap")] = DMXGap;
   dmx["start"] = DMXStart;
@@ -1020,11 +1023,11 @@ void serializeConfig() {
   dmx[F("e131proxy")] = e131ProxyUniverse;
   #endif
 
-  JsonObject usermods_settings = doc.createNestedObject("um");
+  JsonObject usermods_settings = root.createNestedObject("um");
   usermods.addToConfig(usermods_settings);
 
   File f = WLED_FS.open("/cfg.json", "w");
-  if (f) serializeJson(doc, f);
+  if (f) serializeJson(root, f);
   f.close();
   releaseJSONBufferLock();
 
@@ -1037,19 +1040,21 @@ bool deserializeConfigSec() {
 
   if (!requestJSONBufferLock(3)) return false;
 
-  bool success = readObjectFromFile("/wsec.json", nullptr, &doc);
+  bool success = readObjectFromFile("/wsec.json", nullptr, pDoc);
   if (!success) {
     releaseJSONBufferLock();
     return false;
   }
 
-  JsonObject nw_ins_0 = doc["nw"]["ins"][0];
+  JsonObject root = pDoc->as<JsonObject>();
+
+  JsonObject nw_ins_0 = root["nw"]["ins"][0];
   getStringFromJson(clientPass, nw_ins_0["psk"], 65);
 
-  JsonObject ap = doc["ap"];
+  JsonObject ap = root["ap"];
   getStringFromJson(apPass, ap["psk"] , 65);
 
-  [[maybe_unused]] JsonObject interfaces = doc["if"];
+  [[maybe_unused]] JsonObject interfaces = root["if"];
 
 #ifdef WLED_ENABLE_MQTT
   JsonObject if_mqtt = interfaces["mqtt"];
@@ -1060,10 +1065,10 @@ bool deserializeConfigSec() {
   getStringFromJson(hueApiKey, interfaces["hue"][F("key")], 47);
 #endif
 
-  getStringFromJson(settingsPIN, doc["pin"], 5);
+  getStringFromJson(settingsPIN, root["pin"], 5);
   correctPIN = !strlen(settingsPIN);
 
-  JsonObject ota = doc["ota"];
+  JsonObject ota = root["ota"];
   getStringFromJson(otaPass, ota[F("pwd")], 33);
   CJSON(otaLock, ota[F("lock")]);
   CJSON(wifiLock, ota[F("lock-wifi")]);
@@ -1078,17 +1083,19 @@ void serializeConfigSec() {
 
   if (!requestJSONBufferLock(4)) return;
 
-  JsonObject nw = doc.createNestedObject("nw");
+  JsonObject root = pDoc->to<JsonObject>();
+
+  JsonObject nw = root.createNestedObject("nw");
 
   JsonArray nw_ins = nw.createNestedArray("ins");
 
   JsonObject nw_ins_0 = nw_ins.createNestedObject();
   nw_ins_0["psk"] = clientPass;
 
-  JsonObject ap = doc.createNestedObject("ap");
+  JsonObject ap = root.createNestedObject("ap");
   ap["psk"] = apPass;
 
-  [[maybe_unused]] JsonObject interfaces = doc.createNestedObject("if");
+  [[maybe_unused]] JsonObject interfaces = root.createNestedObject("if");
 #ifdef WLED_ENABLE_MQTT
   JsonObject if_mqtt = interfaces.createNestedObject("mqtt");
   if_mqtt["psk"] = mqttPass;
@@ -1098,16 +1105,16 @@ void serializeConfigSec() {
   if_hue[F("key")] = hueApiKey;
 #endif
 
-  doc["pin"] = settingsPIN;
+  root["pin"] = settingsPIN;
 
-  JsonObject ota = doc.createNestedObject("ota");
+  JsonObject ota = root.createNestedObject("ota");
   ota[F("pwd")] = otaPass;
   ota[F("lock")] = otaLock;
   ota[F("lock-wifi")] = wifiLock;
   ota[F("aota")] = aOtaEnabled;
 
   File f = WLED_FS.open("/wsec.json", "w");
-  if (f) serializeJson(doc, f);
+  if (f) serializeJson(root, f);
   f.close();
   releaseJSONBufferLock();
 }

wled00/ir.cpp

@@ -643,8 +643,8 @@ void decodeIRJson(uint32_t code)
   // this may fail for two reasons: ir.json does not exist or IR code not found
   // if the IR code is not found readObjectFromFile() will clean() doc JSON document
   // so we can differentiate between the two
-  readObjectFromFile("/ir.json", objKey, &doc);
-  fdo = doc.as<JsonObject>();
+  readObjectFromFile("/ir.json", objKey, pDoc);
+  fdo = pDoc->as<JsonObject>();
   lastValidCode = 0;
   if (fdo.isNull()) {
     //the received code does not exist

wled00/json.cpp

@@ -1055,7 +1055,7 @@ void serveJson(AsyncWebServerRequest* request)
     servingClient = false;
     return;
   }
-  AsyncJsonResponse *response = new AsyncJsonResponse(&doc, subJson==JSON_PATH_FXDATA || subJson==JSON_PATH_EFFECTS); // will clear and convert JsonDocument into JsonArray if necessary
+  AsyncJsonResponse *response = new AsyncJsonResponse(pDoc, subJson==JSON_PATH_FXDATA || subJson==JSON_PATH_EFFECTS); // will clear and convert JsonDocument into JsonArray if necessary
 
   JsonVariant lDoc = response->getRoot();
 

wled00/mqtt.cpp

@@ -109,8 +109,8 @@ void onMqttMessage(char* topic, char* payload, AsyncMqttClientMessageProperties
       return;
     }
     if (payloadStr[0] == '{') { //JSON API
-      deserializeJson(doc, payloadStr);
-      deserializeState(doc.as<JsonObject>());
+      deserializeJson(*pDoc, payloadStr);
+      deserializeState(pDoc->as<JsonObject>());
     } else { //HTTP API
       String apireq = "win"; apireq += '&'; // reduce flash string usage
       apireq += payloadStr;

wled00/pin_manager.cpp

@@ -238,7 +238,7 @@ bool PinManagerClass::isPinAllocated(byte gpio, PinOwner tag)
 // Check if supplied GPIO is ok to use
 bool PinManagerClass::isPinOk(byte gpio, bool output)
 {
-#ifdef ESP32
+#ifdef ARDUINO_ARCH_ESP32
   if (digitalPinIsValid(gpio)) {
   #if defined(CONFIG_IDF_TARGET_ESP32C3)
     // strapping pins: 2, 8, & 9
@@ -257,6 +257,9 @@ bool PinManagerClass::isPinOk(byte gpio, bool output)
     // GPIO46 is input only and pulled down
   #else
     if (gpio > 5 && gpio < 12) return false;      //SPI flash pins
+    #ifdef BOARD_HAS_PSRAM
+    if (gpio == 16 || gpio == 17) return false;   //PSRAM pins
+    #endif
   #endif
     if (output) return digitalPinCanOutput(gpio);
     else        return true;

wled00/presets.cpp

@@ -27,7 +27,7 @@ static void doSaveState() {
   if (!requestJSONBufferLock(10)) return; // will set fileDoc
 
   initPresetsFile(); // just in case if someone deleted presets.json using /edit
-  JsonObject sObj = doc.to<JsonObject>();
+  JsonObject sObj = pDoc->to<JsonObject>();
 
   DEBUG_PRINTLN(F("Serialize current state"));
   if (playlistSave) {
@@ -42,7 +42,7 @@ static void doSaveState() {
 /*
   #ifdef WLED_DEBUG
     DEBUG_PRINTLN(F("Serialized preset"));
-    serializeJson(doc,Serial);
+    serializeJson(*pDoc,Serial);
     DEBUG_PRINTLN();
   #endif
 */
@@ -83,9 +83,9 @@ bool getPresetName(byte index, String& name)
 {
   if (!requestJSONBufferLock(9)) return false;
   bool presetExists = false;
-  if (readObjectFromFileUsingId(getFileName(), index, &doc))
+  if (readObjectFromFileUsingId(getFileName(), index, pDoc))
   {
-    JsonObject fdo = doc.as<JsonObject>();
+    JsonObject fdo = pDoc->as<JsonObject>();
     if (fdo["n"]) {
       name = (const char*)(fdo["n"]);
       presetExists = true;

wled00/remote.cpp

@@ -123,8 +123,8 @@ static bool remoteJson(int button)
   sprintf_P(objKey, PSTR("\"%d\":"), button);
 
   // attempt to read command from remote.json
-  readObjectFromFile("/remote.json", objKey, &doc);
-  JsonObject fdo = doc.as<JsonObject>();
+  readObjectFromFile("/remote.json", objKey, pDoc);
+  JsonObject fdo = pDoc->as<JsonObject>();
   if (fdo.isNull()) {
     // the received button does not exist
     if (!WLED_FS.exists("/remote.json")) errorFlag = ERR_FS_RMLOAD; //warn if file itself doesn't exist

wled00/set.cpp

@@ -626,7 +626,7 @@ void handleSettingsSet(AsyncWebServerRequest *request, byte subPage)
       }
     }
 
-    JsonObject um = doc.createNestedObject("um");
+    JsonObject um = pDoc->createNestedObject("um");
 
     size_t args = request->args();
     uint16_t j=0;

wled00/udp.cpp

@@ -664,8 +664,8 @@ void handleNotifications()
       apireq += (char*)udpIn;
       handleSet(nullptr, apireq);
     } else if (udpIn[0] == '{') { //JSON API
-      DeserializationError error = deserializeJson(doc, udpIn);
-      JsonObject root = doc.as<JsonObject>();
+      DeserializationError error = deserializeJson(*pDoc, udpIn);
+      JsonObject root = pDoc->as<JsonObject>();
       if (!error && !root.isNull()) deserializeState(root);
     }
     releaseJSONBufferLock();