Schematics...

[dixi83]

Please supply them is you want to sell this board...

[ellensp]

Please provide schematics.

[Mekanikalistik]

Where is the shematics of this board ?

In marlin code there is a line about SERVO PINS

#if MB(RUMBA32_V1_1)

#define SERVO0_PIN PA15
#undef BTN_PIN

Where is this pin located on board ?

[FinnsMax]

PA15 - TP4

[Mekanikalistik]

exactly which point on the board ?

[FinnsMax]

TP4, test paint

[FinnsMax]

https://github.com/makerbase-mks/MKS-RUMBA32/blob/master/hardware/MKS%20RUMBA32%20V1.0_002/MKS%20RUMBA32%20V1.0_002%20TOP.pdf

[Mekanikalistik]

Does MKS RUMB32 have same pinout with BTT rumba32 ?

[FinnsMax]

yes

[Mekanikalistik]

Thank you so much :)

[bagobor]

@FinnsMax I suppose all bugs are here as well? ex: makerbase-mks/MKS-RUMBA32#2

[FinnsMax]

I suppose all bugs are here as well? ex: lack of filters at endstops and thermistor inputs

[dixi83]

It is not the same as the MKS it has many comparable things, for example to get uart drives (like TMC 2208/9) to work, this is what i found after tracing back the board:
pins_RUMBA32_AUS3D.h (which is the pin file BTT uses in there example, the MKS pin file is not even used):

    #define X_SERIAL_TX_PIN                 PC14 //PA14 BTT Rumba32 only uses 1 pin for uart
    #define X_SERIAL_RX_PIN                 PC14

    #define Y_SERIAL_TX_PIN                 PE4 //PA13
    #define Y_SERIAL_RX_PIN                 PE4

    #define Z_SERIAL_TX_PIN                 PE0 //PB10
    #define Z_SERIAL_RX_PIN                 PE0

    #define E0_SERIAL_TX_PIN                PC13 //PD11
    #define E0_SERIAL_RX_PIN                PC13

    #define E1_SERIAL_TX_PIN                PD5 //PB3
    #define E1_SERIAL_RX_PIN                PD5

    #define E2_SERIAL_TX_PIN                PD1 //PB4
    #define E2_SERIAL_RX_PIN                PD1

And I have found more differences and undocumented things. I'll keep this for my self until the lazy company called "bigtreetech" supplied there schematics or unless someone specifically ask for it here. Because the word "support" is not in there dictionary.

[dixi83]

#if MB(RUMBA32_V1_1)

#define SERVO0_PIN PA15
#undef BTN_PIN

Where is this pin located on board ?

to answer a serious question instead of suppling wrong information,
PA15 is not used or wired out on the board, it is located here (the yellow spot near my arrow):

[Mekanikalistik]

Yes, i also checked their marlin software to find correct pins. What are other things you came up with this board.. i have 2 of them.. they are all working fine. Just dont forget to pull down or pull up enstop pins depending on your setup. I am having problems with IR probe and seems like it is solved after i pulled down the Zmin pin (STM32f4 supports internal pull down too)

Currently , i am trying to solve the noise/loud 0.9degree steppers +mks2209 v.2 +24V volt setup and there seems no solution.

[dixi83]

I'm using BLtouch for which I redefined the Z-Max pin as servo, and use the Z-Min pin as probe pin. pin configuration now looks like this:
pins_RUMBA32_common.h :

#define Z_MAX_PIN                           PA15 // PA15 is not connected to anything

pins_RUMBA32_AUS3D.h :

#define SERVO0_PIN                          PD10 // PD10 was Z_MAX_PIN 

I am using TMC2209 without any issues now I had problems with 1 drive, which was not running at al but only making noise, I found out this drive was wired different than the other drives which came from the same order... so I swopped 2 wires and it ran.

Edit: mistake about the pin number PB10 should be PD10 of course...