Add RZ-EasyFPGA A2.2

nmigen_boards/rz_easyfpga_a2_2.py

@@ -0,0 +1,133 @@
+import os
+import subprocess
+
+from nmigen.build import *
+from nmigen.vendor.intel import *
+from .resources import *
+
+
+__all__ = ["RZEasyFPGAA2_2Platform"]
+
+
+class RZEasyFPGAA2_2Platform(IntelPlatform):
+    device      = "EP4CE6" # Cyclone IV 6K LEs
+    package     = "E22"    # EQFP 144 pins
+    speed       = "C8"
+    default_clk = "clk50"  # 50MHz builtin clock
+    default_rst = "rst"
+    resources   = [
+        # Clock
+        Resource("clk50", 0, Pins("23", dir="i"),
+                 Clock(50e6), Attrs(io_standard="3.3-V LVTTL")),
+
+        # Reset switch, located on the lower left of the board.
+        Resource("rst", 0, PinsN("25", dir="i"), Attrs(io_standard="3.3-V LVTTL")),
+
+        # LEDs, located on the bottom of the board.
+        *LEDResources(
+            pins="87 86 85 84", invert=True,
+            attrs=Attrs(io_standard="3.3-V LVTTL")),
+
+        # Buttons, located on the bottom of the board, right of the LEDs.
+        *ButtonResources(
+            pins="88 89 90 91", invert=True,
+            attrs=Attrs(io_standard="3.3-V LVTTL")),
+
+        # Connections to the SKHynix RAM chip on board.
+        SDRAMResource(0,
+            clk="43", cs="72", we="69", ras="71", cas="70",
+            ba="73 74", a="76 77 80 83 68 67 66 65 64 60 75 59",
+            dq="28 30 31 32 33 34 38 39 54 53 52 51 50 49 46 44",
+            dqm="42 55", attrs=Attrs(io_standard="3.3-V LVCMOS")),
+
+        # VGA connector, located on the right of the board.
+        Resource("vga", 0,
+            Subsignal("r", Pins("106", dir="o")),
+            Subsignal("g", Pins("105", dir="o")),
+            Subsignal("b", Pins("104", dir="o")),
+            Subsignal("hs", Pins("101", dir="o")),
+            Subsignal("vs", Pins("103", dir="o")),
+        ),
+
+        # 4 digit 7 segment display, located on top of the board.
+        Display7SegResource(0,
+            a="128", b="121", c="125", d="129", e="132", f="126", g="124", dp="127",
+            invert=True),
+        Resource("display_7seg_ctrl", 0,
+            Subsignal("en", Pins("133 135 136 137", dir="o", invert=True)),
+        ),
+
+        # PS2 port, located on upper right of the board.
+        Resource("ps2_host", 0, 
+            Subsignal("clk", Pins("119", dir="io")),
+            Subsignal("dat", Pins("120", dir="io")),
+        ),
+
+        # LM75 temperature sensor
+        I2CResource(0, scl="112", sda="113"),
+
+        # AT24C08 EEPROM
+        I2CResource(1, scl="99" , sda="98" ),
+
+        # Buzzer
+        Resource("buzzer", 0, PinsN("110", dir="o")),
+
+        # Serial port, located above the VGA port.
+        UARTResource(0, tx="114", rx="115"),
+
+        # LCD connector, located above the 7 segment display.
+        Resource("lcd_hd44780", 0,
+            Subsignal("rs", Pins("141", dir="o")),
+            Subsignal("rw", Pins("138", dir="o")),
+            Subsignal("e" , Pins("143", dir="o")),
+            Subsignal("d" , Pins("142 1 144 3 2 10 7 11", dir="io")),
+        ),
+
+        # IR receiver, located right of the buttons.
+        Resource("cir", 0,
+            Subsignal("rx", Pins("100", dir="i"))
+        ),
+    ]
+
+    connectors  = [
+        # Located above the chip.
+        Connector("gpio", 0,
+            "-   -   11  7   2   144 142 138 136 133 129 127 125 121 119 114 112 110 -  "
+            "-   -   24  10  3   1   143 141 137 135 132 128 126 124 120 115 113 111 -  "),
+
+        # Located right of the chip.
+        Connector("gpio", 1,
+            "-   -  "
+            "106 105"
+            "104 103"
+            "101 100"
+            "99  98 "
+            "91  90 "
+            "89  88 "
+            "87  86 "
+            "85  84 "
+            "-   -  "),
+
+        # Located below the chip.
+        Connector("gpio", 2,
+            "30 32 34 39 43 46 50 52 54 58 60 65 67 71 73 75 77 83 -  -  - "
+            "28 31 33 38 42 44 51 53 55 59 64 66 68 70 72 74 76 80 -  -  - "),
+    ]
+
+    def toolchain_prepare(self, fragment, name, **kwargs):
+        overrides = {
+            "add_settings":
+                '''set_global_assignment -name CYCLONEII_RESERVE_NCEO_AFTER_CONFIGURATION "USE AS REGULAR IO"'''
+        }
+        return super().toolchain_prepare(fragment, name, **overrides, **kwargs)
+
+    def toolchain_program(self, products, name):
+        quartus_pgm = os.environ.get("QUARTUS_PGM", "quartus_pgm")
+        with products.extract("{}.sof".format(name)) as bitstream_filename:
+            subprocess.check_call([quartus_pgm, "--haltcc", "--mode", "JTAG",
+                                   "--operation", "P;" + bitstream_filename])
+
+
+if __name__ == "__main__":
+    from .test.blinky import Blinky
+    RZEasyFPGAA2_2Platform().build(Blinky(), do_program=True)