ZONESTAR_LCD buttons not working

[clifo]

BOARD ZRIB v3.2
Analog keyboard only responds to the button left
Configuration.h.TXT
Configuration_adv.h.TXT

[thinkyhead]

Did it work before but then stop working in a new version of Marlin?

[woutnieuw93]

I have the same issue with 2.0.5, did work on the supplied 1.1.8 firmware from zonestar on my p802qr2
Board is ZRIB V2.2

[woutnieuw93]

I'd like to help you guys get more data, whats needed?

[thinkyhead]

whats needed?

• The working Firmware from Zonestar to compare against.
• A proper ADC_KEYPAD_PIN value for BOARD_ZRIB_V20.
• The output of M43 showing whether any pin conflicts exist.

[clifo]

HI
Only when I press the key to the left, the beeper is activated. It responds to commands from the console (Rpetier - Host).
My English is very weak, I apologize

M0101019 -> 1.1.x "bugfix" snapshot date 03152020 - OK
ZONESTAR_Firmware_V3（Marlin_V1.1.8 ) - original by Zonestar - select MODEL_NUMBER P802QS_5KEY

M020005 -> Marlin 2.0 with bug fixes - date 03192020
M020005.zip
ZRIB_V32_Pinout.pdf
ZRIB_V3_Schematic.pdf
ZRIB_LCD_KEYPAY_SCH V4.pdf
ZONESTAR_Firmware_V3（Marlin_V1.1.8 )(1).zip
M010109.zip

M43 command:

10:29:54.362 : N16 M43*35
10:29:54.362 : PIN: 0 Port: E0 RXD0 protected
10:29:54.378 : PIN: 1 Port: E1 TXD0 protected
10:29:54.393 : PIN: 2 Port: E4 <unused/unknown> Input = 0 TIMER3B PWM: 0 WGM: 1 COM3B: 1 CS: 3 TCCR3A: 1 TCCR3B: 3 TIMSK3: 0
10:29:54.393 : PIN: 3 Port: E5 X_MIN_PIN protected
10:29:54.393 : . X_STOP_PIN protected
10:29:54.424 : PIN: 4 Port: G5 SERVO3_PIN Input = 0 TIMER0B PWM: 128 WGM: 3 COM0B: 3 CS: 3 TCCR0A: 3 TCCR0B: 3 TIMSK0: 5 compare interrupt enabled overflow interrupt enabled
10:29:54.440 : PIN: 5 Port: E3 SERVO2_PIN Input = 0 TIMER3A PWM: 0 WGM: 1 COM3A: 1 CS: 3 TCCR3A: 1 TCCR3B: 3 TIMSK3: 0
10:29:54.456 : PIN: 6 Port: H3 SERVO1_PIN Input = 0 TIMER4A PWM: 0 WGM: 1 COM4A: 1 CS: 3 TCCR4A: 1 TCCR4B: 3 TIMSK4: 0
10:29:54.471 : . ZRIB_V20_D6_PIN Input = 0 TIMER4A PWM: 0 WGM: 1 COM4A: 1 CS: 3 TCCR4A: 1 TCCR4B: 3 TIMSK4: 0
10:29:54.471 : PIN: 7 Port: H4 FAN1_PIN protected
10:29:54.471 : . MOSFET_D_PIN protected
10:29:54.487 : PIN: 8 Port: H5 HEATER_BED_PIN protected
10:29:54.487 : . RAMPS_D8_PIN protected
10:29:54.503 : PIN: 9 Port: H6 FAN_PIN protected
10:29:54.503 : . RAMPS_D9_PIN protected
10:29:54.503 : . ZRIB_V20_D9_PIN protected
10:29:54.518 : PIN: 10 Port: B4 HEATER_0_PIN protected
10:29:54.518 : . RAMPS_D10_PIN protected
10:29:54.549 : PIN: 11 Port: B5 SERVO0_PIN Input = 0 TIMER1A PWM: 2000 WGM: 4 COM1A: 0 CS: 2 TCCR1A: 0 TCCR1B: 10 TIMSK1: 2 non-standard PWM mode compare interrupt enabled
10:29:54.565 : PIN: 12 Port: B6 <unused/unknown> Input = 0 TIMER1B PWM: 0 WGM: 4 COM1B: 0 CS: 2 TCCR1A: 0 TCCR1B: 10 TIMSK1: 2 non-standard PWM mode
10:29:54.581 : PIN: 13 Port: B7 LED_PIN Input = 0 TIMER0A PWM: 0 WGM: 3 COM0A: 3 CS: 3 TCCR0A: 3 TCCR0B: 3 TIMSK0: 5 overflow interrupt enabled
10:29:54.596 : . TIMER1C is also tied to this pin TIMER1C PWM: 0 WGM: 4 COM1C: 0 CS: 2 TCCR1A: 0 TCCR1B: 10 TIMSK1: 2 non-standard PWM mode
10:29:54.596 : PIN: 14 Port: J1 Y_MIN_PIN protected
10:29:54.612 : . Y_STOP_PIN protected
10:29:54.612 : PIN: 15 Port: J0 <unused/unknown> Input = 1
10:29:54.628 : PIN: 16 Port: H1 LCD_PINS_RS Output = 1
10:29:54.628 : PIN: 17 Port: H0 LCD_PINS_ENABLE Output = 0
10:29:54.628 : PIN: 18 Port: D3 Z_MIN_PIN protected
10:29:54.643 : . Z_STOP_PIN protected
10:29:54.643 : PIN: 19 Port: D2 <unused/unknown> Input = 1
10:29:54.659 : PIN: 20 Port: D1 <unused/unknown> Input = 0
10:29:54.674 : PIN: 21 Port: D0 <unused/unknown> Input = 0
10:29:54.674 : PIN: 22 Port: A0 <unused/unknown> Input = 0
10:29:54.690 : PIN: 23 Port: A1 LCD_PINS_D4 Output = 0
10:29:54.690 : PIN: 24 Port: A2 E0_ENABLE_PIN protected
10:29:54.690 : PIN: 25 Port: A3 LCD_PINS_D5 Output = 0
10:29:54.706 : PIN: 26 Port: A4 E0_STEP_PIN protected
10:29:54.706 : PIN: 27 Port: A5 LCD_PINS_D6 Output = 0
10:29:54.721 : PIN: 28 Port: A6 E0_DIR_PIN protected
10:29:54.721 : PIN: 29 Port: A7 LCD_PINS_D7 Output = 0
10:29:54.737 : PIN: 30 Port: C7 E1_ENABLE_PIN Output = 1
10:29:54.737 : PIN: 31 Port: C6 <unused/unknown> Input = 0
10:29:54.737 : PIN: 32 Port: C5 Z_MIN_PROBE_PIN protected
10:29:54.753 : PIN: 33 Port: C4 <unused/unknown> Input = 1
10:29:54.753 : PIN: 34 Port: C3 E1_DIR_PIN Output = 0
10:29:54.768 : PIN: 35 Port: C2 <unused/unknown> Input = 1
10:29:54.768 : PIN: 36 Port: C1 E1_STEP_PIN Input = 0
10:29:54.784 : PIN: 37 Port: C0 BEEPER_PIN Output = 0
10:29:54.784 : PIN: 38 Port: D7 X_ENABLE_PIN protected
10:29:54.799 : PIN: 39 Port: G2 <unused/unknown> Input = 0
10:29:54.799 : PIN: 40 Port: G1 E_MUX0_PIN Input = 0
10:29:54.815 : . SHIFT_OUT Input = 0
10:29:54.815 : PIN: 41 Port: G0 <unused/unknown> Input = 1
10:29:54.831 : PIN: 42 Port: L7 E_MUX1_PIN Input = 0
10:29:54.831 : . SHIFT_LD Input = 0
10:29:54.846 : PIN: 43 Port: L6 <unused/unknown> Input = 0
10:29:54.862 : PIN: 44 Port: L5 E_MUX2_PIN Input = 0 TIMER5C PWM: 0 WGM: 1 COM5C: 0 CS: 3 TCCR5A: 1 TCCR5B: 3 TIMSK5: 0
10:29:54.878 : . E1_CS_PIN Input = 0 TIMER5C PWM: 0 WGM: 1 COM5C: 0 CS: 3 TCCR5A: 1 TCCR5B: 3 TIMSK5: 0
10:29:54.878 : . SHIFT_CLK Input = 0
10:29:54.893 : PIN: 45 Port: L4 <unused/unknown> Input = 0 TIMER5B PWM: 0 WGM: 1 COM5B: 1 CS: 3 TCCR5A: 1 TCCR5B: 3 TIMSK5: 0
10:29:54.909 : PIN: 46 Port: L3 Z_STEP_PIN protected
10:29:54.909 : PIN: 47 Port: L2 <unused/unknown> Input = 0
10:29:54.909 : PIN: 48 Port: L1 Z_DIR_PIN protected
10:29:54.924 : PIN: 49 Port: L0 <unused/unknown> Input = 1
10:29:54.924 : PIN: 50 Port: B3 AVR_MISO_PIN Input = 0
10:29:54.940 : . MISO_PIN Input = 0
10:29:54.940 : PIN: 51 Port: B2 AVR_MOSI_PIN Output = 1
10:29:54.956 : . MOSI_PIN Output = 1
10:29:54.956 : PIN: 52 Port: B1 AVR_SCK_PIN Output = 0
10:29:54.971 : . SCK_PIN Output = 0
10:29:54.971 : PIN: 53 Port: B0 AVR_SS_PIN Output = 1
10:29:54.971 : . SDSS Output = 1
10:29:54.987 : . SS_PIN Output = 1
10:29:54.987 : PIN: 54 Port: F0 (A 0) X_STEP_PIN protected
10:29:55.003 : PIN: 55 Port: F1 (A 1) X_DIR_PIN protected
10:29:55.003 : PIN: 56 Port: F2 (A 2) Y_ENABLE_PIN protected
10:29:55.018 : PIN: 57 Port: F3 (A 3) <unused/unknown> Analog in = 820 Input = 1
10:29:55.018 : PIN: 58 Port: F4 (A 4) <unused/unknown> Analog in = 807 Input = 1
10:29:55.034 : PIN: 59 Port: F5 (A 5) BTN_EN2 Input = 1
10:29:55.034 : PIN: 60 Port: F6 (A 6) Y_STEP_PIN protected
10:29:55.049 : PIN: 61 Port: F7 (A 7) Y_DIR_PIN protected
10:29:55.049 : PIN: 62 Port: K0 (A 8) Z_ENABLE_PIN protected
10:29:55.049 : PIN: 63 Port: K1 (A 9) BTN_ENC Input = 1
10:29:55.065 : PIN: 64 Port: K2 (A10) BTN_EN1 Input = 0
10:29:55.065 : PIN: 65 Port: K3 (A11) <unused/unknown> Analog in = 840 Input = 1
10:29:55.081 : PIN: 66 Port: K4 (A12) MAX6675_SS_PIN Input = 1
10:29:55.081 : PIN: 67 Port: K5 (A13) <unused/unknown> Analog in = 985 Input = 0
10:29:55.096 : PIN: 68 Port: K6 (A14) <unused/unknown> Analog in = 984 Input = 0
10:29:55.112 : PIN: 69 Port: K7 (A15) <unused/unknown> Analog in = 1023 Input = 1

[bcdiaconu]

Any news on this? I have the exact same problem. Zonestar P802Qs with ZRIV v3.1 and LCD2004 ADCKEY

[bcdiaconu]

If needed, can find configs I've done for this printer here https://github.com/bcdiaconu/Marlin/tree/2.0.x/Marlin

[bcdiaconu]

News: If I press center button in combination with up it will enter Menu. If inside menu I press center buttn + down will go down. But it seems to me that center button + up results not only as center button but rather a sequence of buttons.

[bcdiaconu]

It seems to me that center+up is doing a combination of up+center. center+down is doing a down.

Can you please help with this?

[bcdiaconu]

Left button does a back followed by down.

I entered in menu -> About Printer -> Board Info and it shows "MKS Gen >0 v1.3" instead of ZRIB

[ellensp]

P802QS_5KEY uses A10 for ADC_KEYPAD
the file says

static const stADCKeypadTable stADCKeyTable[] PROGMEM = {
// VALUE_MIN, VALUE_MAX, KEY
{ 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F1 + 1 }, // F1
{ 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F2 + 1 }, // F2
{ 4000, 4096, BLEN_REPRAPWORLD_KEYPAD_F3 + 1 }, // F3
{ 300, 500, BLEN_REPRAPWORLD_KEYPAD_LEFT + 1 }, // LEFT
{ 1900, 2200, BLEN_REPRAPWORLD_KEYPAD_RIGHT + 1 }, // RIGHT
{ 570, 870, BLEN_REPRAPWORLD_KEYPAD_UP + 1 }, // UP
{ 2670, 2870, BLEN_REPRAPWORLD_KEYPAD_DOWN + 1 }, // DOWN
{ 1150, 1450, BLEN_REPRAPWORLD_KEYPAD_MIDDLE + 1 }, // ENTER
};

but marlin 2 doesnt do it this way...