Update 5.4.x+fslc to v5.4.56#97
Merged
otavio merged 88 commits intoFreescale:5.4.x+fslcfrom Aug 5, 2020
Merged
Conversation
[ Upstream commit 128c664 ] Release all allocated memory if sha type is invalid: In ccp_run_sha_cmd, if the type of sha is invalid, the allocated hmac_buf should be released. v2: fix the goto. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b2df7 ] In cx23888_ir_probe if kfifo_alloc fails the allocated memory for state should be released. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f45db2b ] The domain table should be empty at module unload. If it isn't there is a bug somewhere. So check and report. Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651 Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cc78dc3 upstream. For all data packets transmitted, host gets htt tx completion event. Some QCA9984 firmware releases support WMI_SERVICE_TX_DATA_ACK_RSSI, which gives data ack rssi values to host through htt event of data tx completion. Data ack rssi values are valid if A0 bit is set in HTT rx message. So enable the feature also for QCA9884. Tested HW: QCA9984 Tested FW: 10.4-3.9.0.2-00044 Signed-off-by: Abhishek Ambure <aambure@codeaurora.org> Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org> [kvalo@codeaurora.org: improve commit log] Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b361663 upstream. Recently ASPM handling was changed to allow ASPM on PCIe-to-PCI/PCI-X bridges. Unfortunately the ASMedia ASM1083/1085 PCIe to PCI bridge device doesn't seem to function properly with ASPM enabled. On an Asus PRIME H270-PRO motherboard, it causes errors like these: pcieport 0000:00:1c.0: AER: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID) pcieport 0000:00:1c.0: AER: device [8086:a292] error status/mask=00003000/00002000 pcieport 0000:00:1c.0: AER: [12] Timeout pcieport 0000:00:1c.0: AER: Corrected error received: 0000:00:1c.0 pcieport 0000:00:1c.0: AER: can't find device of ID00e0 In addition to flooding the kernel log, this also causes the machine to wake up immediately after suspend is initiated. The device advertises ASPM L0s and L1 support in the Link Capabilities register, but the ASMedia web page for ASM1083 [1] claims "No PCIe ASPM support". Windows 10 (build 2004) enables L0s, but it also logs correctable PCIe errors. Add a quirk to disable ASPM for this device. [1] https://www.asmedia.com.tw/eng/e_show_products.php?cate_index=169&item=114 [bhelgaas: commit log] Fixes: 66ff14e ("PCI/ASPM: Allow ASPM on links to PCIe-to-PCI/PCI-X Bridges") Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208667 Link: https://lore.kernel.org/r/20200722021803.17958-1-hancockrwd@gmail.com Signed-off-by: Robert Hancock <hancockrwd@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c72fee upstream. When handling a page fault, we drop mmap_sem to start async readahead so that we don't block on IO submission with mmap_sem held. However there's no point to drop mmap_sem in case readahead is disabled. Handle that case to avoid pointless dropping of mmap_sem and retrying the fault. This was actually reported to block mlockall(MCL_CURRENT) indefinitely. Fixes: 6b4c9f4 ("filemap: drop the mmap_sem for all blocking operations") Reported-by: Minchan Kim <minchan@kernel.org> Reported-by: Robert Stupp <snazy@gmx.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Minchan Kim <minchan@kernel.org> Link: http://lkml.kernel.org/r/20200212101356.30759-1-jack@suse.cz Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: SeongJae Park <sjpark@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3da87ec upstream. As expected, this requires the same quirk as the SSL2+ in order for the clock to sync. This was suggested by, and tested on an SSL2, by Dmitry. Suggested-by: Dmitry <dpavlushko@gmail.com> Signed-off-by: Laurence Tratt <laurie@tratt.net> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200621075005.52mjjfc6dtdjnr3h@overdrive.tratt.net Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
… series with ALC289 commit 4b43d05 upstream. This patch adds support for headset mic to the ASUS ROG Zephyrus G15(GA502) notebook series by adding the corresponding vendor/pci_device id, as well as adding a new fixup for the used realtek ALC289. The fixup stets the correct pin to get the headset mic correctly recognized on audio-jack. Signed-off-by: Armas Spann <zappel@retarded.farm> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200724140616.298892-1-zappel@retarded.farm Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…G14(GA401) series with ALC289 commit 293a92c upstream. This patch fixes a small typo I accidently submitted with the initial patch. The board should be named GA401 not G401. Fixes: ff53664 ("ALSA: hda/realtek: enable headset mic of ASUS ROG Zephyrus G14(G401) series with ALC289") Signed-off-by: Armas Spann <zappel@retarded.farm> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200724140837.302763-1-zappel@retarded.farm Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…erence board (alc256) commit 6fa38ef upstream. Intel requires to enable power saving mode for intel reference board (alc256) Signed-off-by: PeiSen Hou <pshou@realtek.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200727115647.10967-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5649625 upstream. HP NB right speaker had no sound output. This platform was connected to I2S Amp for speaker out.(None Realtek I2S Amp IC) EC need to check codec GPIO1 pin to initial I2S Amp. Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/01285f623ac7447187482fb4a8ecaa7c@realtek.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2c3657 upstream. It's been reported that, when neither nouveau nor Nvidia graphics driver is used, the screen starts flickering. And, after comparing between the working case (stable 4.4.x) and the broken case, it turned out that the problem comes from the audio component binding. The Nvidia and AMD audio binding code clears the bus->keep_power flag whenever snd_hdac_acomp_init() succeeds. But this doesn't mean that the component is actually bound, but it merely indicates that it's ready for binding. So, when both nouveau and Nvidia are blacklisted or not ready, the driver keeps running without the audio component but also with bus->keep_power = false. This made the driver runtime PM kicked in and powering down when unused, which results in flickering in the graphics side, as it seems. For fixing the bug, this patch moves the bus->keep_power flag change into generic_acomp_notifier_set() that is the function called from the master_bind callback of component ops; i.e. it's guaranteed that the binding succeeded. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208609 Fixes: 5a858e7 ("ALSA: hda - Disable audio component for legacy Nvidia HDMI codecs") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200728082033.23933-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54a485e upstream. The lookaside count is improperly initialized to the size of the Receive Queue with the additional +1. In the traces below, the RQ size is 384, so the count was set to 385. The lookaside count is then rarely refreshed. Note the high and incorrect count in the trace below: rvt_get_rwqe: [hfi1_0] wqe ffffc900078e9008 wr_id 55c7206d75a0 qpn c qpt 2 pid 3018 num_sge 1 head 1 tail 0, count 385 rvt_get_rwqe: (hfi1_rc_rcv+0x4eb/0x1480 [hfi1] <- rvt_get_rwqe) ret=0x1 The head,tail indicate there is only one RWQE posted although the count says 385 and we correctly return the element 0. The next call to rvt_get_rwqe with the decremented count: rvt_get_rwqe: [hfi1_0] wqe ffffc900078e9058 wr_id 0 qpn c qpt 2 pid 3018 num_sge 0 head 1 tail 1, count 384 rvt_get_rwqe: (hfi1_rc_rcv+0x4eb/0x1480 [hfi1] <- rvt_get_rwqe) ret=0x1 Note that the RQ is empty (head == tail) yet we return the RWQE at tail 1, which is not valid because of the bogus high count. Best case, the RWQE has never been posted and the rc logic sees an RWQE that is too small (all zeros) and puts the QP into an error state. In the worst case, a server slow at posting receive buffers might fool rvt_get_rwqe() into fetching an old RWQE and corrupt memory. Fix by deleting the faulty initialization code and creating an inline to fetch the posted count and convert all callers to use new inline. Fixes: f592ae3 ("IB/rdmavt: Fracture single lock used for posting and processing RWQEs") Link: https://lore.kernel.org/r/20200728183848.22226.29132.stgit@awfm-01.aw.intel.com Reported-by: Zhaojuan Guo <zguo@redhat.com> Cc: <stable@vger.kernel.org> # 5.4.x Reviewed-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Tested-by: Honggang Li <honli@redhat.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 295c1b9 upstream. vhost/scsi doesn't handle type conversion correctly for request type when using virtio 1.0 and up for BE, or cross-endian platforms. Fix it up using vhost_32_to_cpu. Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…ad_work commit 74d6a5d upstream. p9_read_work and p9_fd_cancelled may be called concurrently. In some cases, req->req_list may be deleted by both p9_read_work and p9_fd_cancelled. We can fix it by ignoring replies associated with a cancelled request and ignoring cancelled request if message has been received before lock. Link: http://lkml.kernel.org/r/20200612090833.36149-1-wanghai38@huawei.com Fixes: 60ff779 ("9p: client: remove unused code and any reference to "cancelled" function") Cc: <stable@vger.kernel.org> # v3.12+ Reported-by: syzbot+77a25acfa0382e06ab23@syzkaller.appspotmail.com Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6989310 upstream. Use offsetof to calculate offset of a field to take advantage of compiler built-in version when possible, and avoid UBSAN warning when compiling with Clang: ================================================================== UBSAN: Undefined behaviour in net/wireless/wext-core.c:525:14 member access within null pointer of type 'struct iw_point' CPU: 3 PID: 165 Comm: kworker/u16:3 Tainted: G S W 4.19.23 Freescale#43 Workqueue: cfg80211 __cfg80211_scan_done [cfg80211] Call trace: dump_backtrace+0x0/0x194 show_stack+0x20/0x2c __dump_stack+0x20/0x28 dump_stack+0x70/0x94 ubsan_epilogue+0x14/0x44 ubsan_type_mismatch_common+0xf4/0xfc __ubsan_handle_type_mismatch_v1+0x34/0x54 wireless_send_event+0x3cc/0x470 ___cfg80211_scan_done+0x13c/0x220 [cfg80211] __cfg80211_scan_done+0x28/0x34 [cfg80211] process_one_work+0x170/0x35c worker_thread+0x254/0x380 kthread+0x13c/0x158 ret_from_fork+0x10/0x18 =================================================================== Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20191204081307.138765-1-pihsun@chromium.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…watchpoints commit eec13b4 upstream. Unprivileged memory accesses generated by the so-called "translated" instructions (e.g. LDRT) in kernel mode can cause user watchpoints to fire unexpectedly. In such cases, the hw_breakpoint logic will invoke the user overflow handler which will typically raise a SIGTRAP back to the current task. This is futile when returning back to the kernel because (a) the signal won't have been delivered and (b) userspace can't handle the thing anyway. Avoid invoking the user overflow handler for watchpoints triggered by kernel uaccess routines, and instead single-step over the faulting instruction as we would if no overflow handler had been installed. Cc: <stable@vger.kernel.org> Fixes: f81ef4a ("ARM: 6356/1: hw-breakpoint: add ARM backend for the hw-breakpoint framework") Reported-by: Luis Machado <luis.machado@linaro.org> Tested-by: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d36f260 upstream. Commit 0672d22 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the phy-mode for fec1, but missed to fix it for the fec2 node. Fix fec2 to also use "rgmii-id" as the phy-mode. Cc: <stable@vger.kernel.org> Fixes: 0672d22 ("ARM: dts: imx: Fix the AR803X phy-mode") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c696afd upstream. Commit 0672d22 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the phy-mode for fec1, but missed to fix it for the fec2 node. Fix fec2 to also use "rgmii-id" as the phy-mode. Cc: <stable@vger.kernel.org> Fixes: 0672d22 ("ARM: dts: imx: Fix the AR803X phy-mode") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a601da upstream. The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID because of which when card is inserted, usb otg is enumerated and the card is never detected. [ 64.492645] cfg80211: failed to load regulatory.db [ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2 [ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 76.412763] usb usb2: Product: EHCI Host Controller [ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd [ 76.424623] usb usb2: SerialNumber: ci_hdrc.0 [ 76.431755] hub 2-0:1.0: USB hub found [ 76.435862] hub 2-0:1.0: 1 port detected The TRM mentions GPIO_1 pad should be muxed/assigned for card detect and ENET_RX_ER pad for USB_OTG_ID for proper operation. This patch fixes pin muxing as per TRM and is tested on a i.Core 1.5 MX6 DL SOM. [ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable [ 22.459992] mmc0: new high speed SDHC card at address 0001 [ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB [ 22.478856] mmcblk0: p1 p2 Fixes: 6df1128 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support") Cc: stable@vger.kernel.org Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 168c358 upstream. free cmd id is read using virtio endian, spec says all fields in balloon are LE. Fix it up. Fixes: 86a5597 ("virtio-balloon: VIRTIO_BALLOON_F_FREE_PAGE_HINT") Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Wei Wang <wei.w.wang@intel.com> Acked-by: David Hildenbrand <david@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87004ab upstream. This regressed some working configurations so revert it. Will fix this properly for 5.9 and backport then. This reverts commit 38e0c89. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fde9f39 upstream. This patch fixes a race condition that causes a use-after-free during amdgpu_dm_atomic_commit_tail. This can occur when 2 non-blocking commits are requested and the second one finishes before the first. Essentially, this bug occurs when the following sequence of events happens: 1. Non-blocking commit Freescale#1 is requested w/ a new dm_state Freescale#1 and is deferred to the workqueue. 2. Non-blocking commit Freescale#2 is requested w/ a new dm_state Freescale#2 and is deferred to the workqueue. 3. Commit Freescale#2 starts before commit Freescale#1, dm_state Freescale#1 is used in the commit_tail and commit Freescale#2 completes, freeing dm_state Freescale#1. 4. Commit Freescale#1 starts after commit Freescale#2 completes, uses the freed dm_state 1 and dereferences a freelist pointer while setting the context. Since this bug has only been spotted with fast commits, this patch fixes the bug by clearing the dm_state instead of using the old dc_state for fast updates. In addition, since dm_state is only used for its dc_state and amdgpu_dm_atomic_commit_tail will retain the dc_state if none is found, removing the dm_state should not have any consequences in fast updates. This use-after-free bug has existed for a while now, but only caused a noticeable issue starting from 5.7-rc1 due to 3202fa6 ("slub: relocate freelist pointer to middle of object") moving the freelist pointer from dm_state->base (which was unused) to dm_state->context (which is dereferenced). Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207383 Fixes: bd200d1 ("drm/amd/display: Don't replace the dc_state for fast updates") Reported-by: Duncan <1i5t5.duncan@cox.net> Signed-off-by: Mazin Rezk <mnrzk@protonmail.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 543e866 upstream. Compiler leaves a 4-byte hole near the end of `dev_info`, causing amdgpu_info_ioctl() to copy uninitialized kernel stack memory to userspace when `size` is greater than 356. In 2015 we tried to fix this issue by doing `= {};` on `dev_info`, which unfortunately does not initialize that 4-byte hole. Fix it by using memset() instead. Cc: stable@vger.kernel.org Fixes: c193fa9 ("drm/amdgpu: information leak in amdgpu_info_ioctl()") Fixes: d38ceaf ("drm/amdgpu: add core driver (v4)") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 900ab59 upstream. The function mipi_dbi_spi1_transfer() will transfer its payload as 9-bit data, the 9th (MSB) bit being the data/command bit. In order to do that, it unpacks the 8-bit values into 16-bit values, then sets the 9th bit if the byte corresponds to data, clears it otherwise. The 7 MSB are padding. The array of now 16-bit values is then passed to the SPI core for transfer. This function was broken since its introduction, as the length of the SPI transfer was set to the payload size before its conversion, but the payload doubled in size due to the 8-bit -> 16-bit conversion. Fixes: 02dd95f ("drm/tinydrm: Add MIPI DBI support") Cc: <stable@vger.kernel.org> # 5.4+ Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200703141341.1266263-1-paul@crapouillou.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8490d6a upstream. A use-after-free in drm_gem_open_ioctl can happen if the GEM object handle is closed between the idr lookup and retrieving the size from said object since a local reference is not being held at that point. Hold the local reference while the object can still be accessed to fix this and plug the potential security hole. Signed-off-by: Steve Cohen <cohens@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1595284250-31580-1-git-send-email-cohens@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbc8a99 upstream. rds_notify_queue_get() is potentially copying uninitialized kernel stack memory to userspace since the compiler may leave a 4-byte hole at the end of `cmsg`. In 2016 we tried to fix this issue by doing `= { 0 };` on `cmsg`, which unfortunately does not always initialize that 4-byte hole. Fix it by using memset() instead. Cc: stable@vger.kernel.org Fixes: f037590 ("rds: fix a leak of kernel memory") Fixes: bdbe6fb ("RDS: recv.c") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39efdd9 upstream. In binutils 2.35, 'nm -D' changed to show symbol versions along with symbol names, with the usual @@ separator. When generating libtraceevent-dynamic-list we need just the names, so strip off the version suffix if present. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: linux-trace-devel@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4becb7e upstream. x25_connect() invokes x25_get_neigh(), which returns a reference of the specified x25_neigh object to "x25->neighbour" with increased refcnt. When x25 connect success and returns, the reference still be hold by "x25->neighbour", so the refcount should be decreased in x25_disconnect() to keep refcount balanced. The reference counting issue happens in x25_disconnect(), which forgets to decrease the refcnt increased by x25_get_neigh() in x25_connect(), causing a refcnt leak. Fix this issue by calling x25_neigh_put() before x25_disconnect() returns. Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8999dc8 upstream. We should check null before do x25_neigh_put in x25_disconnect, otherwise may cause null-ptr-deref like this: #include <sys/socket.h> #include <linux/x25.h> int main() { int sck_x25; sck_x25 = socket(AF_X25, SOCK_SEQPACKET, 0); close(sck_x25); return 0; } BUG: kernel NULL pointer dereference, address: 00000000000000d8 CPU: 0 PID: 4817 Comm: t2 Not tainted 5.7.0-rc3+ Freescale#159 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3- RIP: 0010:x25_disconnect+0x91/0xe0 Call Trace: x25_release+0x18a/0x1b0 __sock_release+0x3d/0xc0 sock_close+0x13/0x20 __fput+0x107/0x270 ____fput+0x9/0x10 task_work_run+0x6d/0xb0 exit_to_usermode_loop+0x102/0x110 do_syscall_64+0x23c/0x260 entry_SYSCALL_64_after_hwframe+0x49/0xb3 Reported-by: syzbot+6db548b615e5aeefdce2@syzkaller.appspotmail.com Fixes: 4becb7e ("net/x25: Fix x25_neigh refcnt leak when x25 disconnect") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e692139 ] The function invokes bpf_prog_inc(), which increases the reference count of a bpf_prog object "rq->xdp_prog" if the object isn't NULL. The refcount leak issues take place in two error handling paths. When either mlx5_wq_ll_create() or mlx5_wq_cyc_create() fails, the function simply returns the error code and forgets to drop the reference count increased earlier, causing a reference count leak of "rq->xdp_prog". Fix this issue by jumping to the error handling path err_rq_wq_destroy while either function fails. Fixes: 422d4c4 ("net/mlx5e: RX, Split WQ objects for different RQ types") Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd3c628 ] When recording with cache-misses and arm_spe_x event, I found that it will just fail without showing any error info if i put cache-misses after 'arm_spe_x' event. [root@localhost 0620]# perf record -e cache-misses \ -e arm_spe_0/ts_enable=1,pct_enable=1,pa_enable=1,load_filter=1,jitter=1,store_filter=1,min_latency=0/ sleep 1 [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.067 MB perf.data ] [root@localhost 0620]# [root@localhost 0620]# perf record -e arm_spe_0/ts_enable=1,pct_enable=1,pa_enable=1,load_filter=1,jitter=1,store_filter=1,min_latency=0/ \ -e cache-misses sleep 1 [root@localhost 0620]# The current code can only work if the only event to be traced is an 'arm_spe_x', or if it is the last event to be specified. Otherwise the last event type will be checked against all the arm_spe_pmus[i]->types, none will match and an out of bound 'i' index will be used in arm_spe_recording_init(). We don't support concurrent multiple arm_spe_x events currently, that is checked in arm_spe_recording_options(), and it will show the relevant info. So add the check and record of the first found 'arm_spe_pmu' to fix this issue here. Fixes: ffd3d18 ("perf tools: Add ARM Statistical Profiling Extensions (SPE) support") Signed-off-by: Wei Li <liwei391@huawei.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Tested-by-by: Leo Yan <leo.yan@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kim Phillips <kim.phillips@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20200724071111.35593-2-liwei391@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fda2ec6 ] When vxlan interface is deleted, all fdbs are deleted by vxlan_flush(). vxlan_flush() flushes fdbs but it doesn't delete fdb, which contains all-zeros-mac because it is deleted by vxlan_uninit(). But vxlan_uninit() deletes only the fdb, which contains both all-zeros-mac and default vni. So, the fdb, which contains both all-zeros-mac and non-default vni will not be deleted. Test commands: ip link add vxlan0 type vxlan dstport 4789 external ip link set vxlan0 up bridge fdb add to 00:00:00:00:00:00 dst 172.0.0.1 dev vxlan0 via lo \ src_vni 10000 self permanent ip link del vxlan0 kmemleak reports as follows: unreferenced object 0xffff9486b25ced88 (size 96): comm "bridge", pid 2151, jiffies 4294701712 (age 35506.901s) hex dump (first 32 bytes): 02 00 00 00 ac 00 00 01 40 00 09 b1 86 94 ff ff ........@....... 46 02 00 00 00 00 00 00 a7 03 00 00 12 b5 6a 6b F.............jk backtrace: [<00000000c10cf651>] vxlan_fdb_append.part.51+0x3c/0xf0 [vxlan] [<000000006b31a8d9>] vxlan_fdb_create+0x184/0x1a0 [vxlan] [<0000000049399045>] vxlan_fdb_update+0x12f/0x220 [vxlan] [<0000000090b1ef00>] vxlan_fdb_add+0x12a/0x1b0 [vxlan] [<0000000056633c2c>] rtnl_fdb_add+0x187/0x270 [<00000000dd5dfb6b>] rtnetlink_rcv_msg+0x264/0x490 [<00000000fc44dd54>] netlink_rcv_skb+0x4a/0x110 [<00000000dff433e7>] netlink_unicast+0x18e/0x250 [<00000000b87fb421>] netlink_sendmsg+0x2e9/0x400 [<000000002ed55153>] ____sys_sendmsg+0x237/0x260 [<00000000faa51c66>] ___sys_sendmsg+0x88/0xd0 [<000000006c3982f1>] __sys_sendmsg+0x4e/0x80 [<00000000a8f875d2>] do_syscall_64+0x56/0xe0 [<000000003610eefa>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 unreferenced object 0xffff9486b1c40080 (size 128): comm "bridge", pid 2157, jiffies 4294701754 (age 35506.866s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 f8 dc 42 b2 86 94 ff ff ..........B..... 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk backtrace: [<00000000a2981b60>] vxlan_fdb_create+0x67/0x1a0 [vxlan] [<0000000049399045>] vxlan_fdb_update+0x12f/0x220 [vxlan] [<0000000090b1ef00>] vxlan_fdb_add+0x12a/0x1b0 [vxlan] [<0000000056633c2c>] rtnl_fdb_add+0x187/0x270 [<00000000dd5dfb6b>] rtnetlink_rcv_msg+0x264/0x490 [<00000000fc44dd54>] netlink_rcv_skb+0x4a/0x110 [<00000000dff433e7>] netlink_unicast+0x18e/0x250 [<00000000b87fb421>] netlink_sendmsg+0x2e9/0x400 [<000000002ed55153>] ____sys_sendmsg+0x237/0x260 [<00000000faa51c66>] ___sys_sendmsg+0x88/0xd0 [<000000006c3982f1>] __sys_sendmsg+0x4e/0x80 [<00000000a8f875d2>] do_syscall_64+0x56/0xe0 [<000000003610eefa>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 3ad7a4b ("vxlan: support fdb and learning in COLLECT_METADATA mode") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e048401 ] On sparc32, tcflag_t is "unsigned long", unlike on all other architectures, where it is "unsigned int": drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’: include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=] drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’ hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n", ^~~~~~~ include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=] drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’ hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n", ^~~~~~~ As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t parameters to "unsigned int". While at it, use "%u" to format unsigned numbers. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 651149f ] During setup(): ... for ns in h0 r1 h1 h2 h3 do create_ns ${ns} done ... while in cleanup(): ... for n in h1 r1 h2 h3 h4 do ip netns del ${n} 2>/dev/null done ... and after removing the stderr redirection in cleanup(): $ sudo ./fib_nexthop_multiprefix.sh ... TEST: IPv4: host 0 to host 3, mtu 1400 [ OK ] TEST: IPv6: host 0 to host 3, mtu 1400 [ OK ] Cannot remove namespace file "/run/netns/h4": No such file or directory $ echo $? 1 and a non-zero return code, make kselftests fail (even if the test itself is fine): ... not ok 34 selftests: net: fib_nexthop_multiprefix.sh # exit=1 ... Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d61e21 ] This is likely firmware causing this but its starting to annoy customers. Change the message level to verbose to prevent the spam. Note that this seems to only show up with ISCSI enabled on the HBA via the qedi driver. Signed-off-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aba69d4 ] Fix ip_defrag.sh when CONFIG_NF_DEFRAG_IPV6=m: $ sudo ./ip_defrag.sh + set -e + mktemp -u XXXXXX + readonly NETNS=ns-rGlXcw + trap cleanup EXIT + setup + ip netns add ns-rGlXcw + ip -netns ns-rGlXcw link set lo up + ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_high_thresh=9000000 + ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_low_thresh=7000000 + ip netns exec ns-rGlXcw sysctl -w net.ipv4.ipfrag_time=1 + ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_high_thresh=9000000 + ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_low_thresh=7000000 + ip netns exec ns-rGlXcw sysctl -w net.ipv6.ip6frag_time=1 + ip netns exec ns-rGlXcw sysctl -w net.netfilter.nf_conntrack_frag6_high_thresh=9000000 + cleanup + ip netns del ns-rGlXcw $ ls -la /proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh ls: cannot access '/proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh': No such file or directory $ sudo modprobe nf_defrag_ipv6 $ ls -la /proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh -rw-r--r-- 1 root root 0 Jul 14 12:34 /proc/sys/net/netfilter/nf_conntrack_frag6_high_thresh Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e8fd3a ] The implementation of s3fwrn5_recv_frame() is supposed to consume skb on all execution paths. Release skb before returning -ENODEV. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f0dcfb ] I/O requests may be held in scheduler queue because of resource contention. The starvation scenario was handled properly in the regular completion path but we failed to account for it during I/O submission. This lead to the hang captured below. Make sure we run the queue when resource contention is encountered in the submission path. [ 39.054963] scsi 13:0:0:0: rejecting I/O to dead device [ 39.058700] scsi 13:0:0:0: rejecting I/O to dead device [ 39.087855] sd 13:0:0:1: [sdd] Synchronizing SCSI cache [ 39.088909] scsi 13:0:0:1: rejecting I/O to dead device [ 39.095351] scsi 13:0:0:1: rejecting I/O to dead device [ 39.096962] scsi 13:0:0:1: rejecting I/O to dead device [ 247.021859] INFO: task scsi-stress-rem:813 blocked for more than 122 seconds. [ 247.023258] Not tainted 5.8.0-rc2 Freescale#8 [ 247.024069] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 247.025331] scsi-stress-rem D 0 813 802 0x00004000 [ 247.025334] Call Trace: [ 247.025354] __schedule+0x504/0x55f [ 247.027987] schedule+0x72/0xa8 [ 247.027991] blk_mq_freeze_queue_wait+0x63/0x8c [ 247.027994] ? do_wait_intr_irq+0x7a/0x7a [ 247.027996] blk_cleanup_queue+0x4b/0xc9 [ 247.028000] __scsi_remove_device+0xf6/0x14e [ 247.028002] scsi_remove_device+0x21/0x2b [ 247.029037] sdev_store_delete+0x58/0x7c [ 247.029041] kernfs_fop_write+0x10d/0x14f [ 247.031281] vfs_write+0xa2/0xdf [ 247.032670] ksys_write+0x6b/0xb3 [ 247.032673] do_syscall_64+0x56/0x82 [ 247.034053] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 247.034059] RIP: 0033:0x7f69f39e9008 [ 247.036330] Code: Bad RIP value. [ 247.036331] RSP: 002b:00007ffdd8116498 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 247.037613] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f69f39e9008 [ 247.039714] RDX: 0000000000000002 RSI: 000055cde92a0ab0 RDI: 0000000000000001 [ 247.039715] RBP: 000055cde92a0ab0 R08: 000000000000000a R09: 00007f69f3a79e80 [ 247.039716] R10: 000000000000000a R11: 0000000000000246 R12: 00007f69f3abb780 [ 247.039717] R13: 0000000000000002 R14: 00007f69f3ab6740 R15: 0000000000000002 Link: https://lore.kernel.org/r/20200720025435.812030-1-ming.lei@redhat.com Cc: linux-block@vger.kernel.org Cc: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b344d6a ] The kernel test bot reported[1] that using set_mask_bits on a u8 causes the following issue on parisc: hppa-linux-ld: drivers/phy/ti/phy-tusb1210.o: in function `tusb1210_probe': >> (.text+0x2f4): undefined reference to `__cmpxchg_called_with_bad_pointer' >> hppa-linux-ld: (.text+0x324): undefined reference to `__cmpxchg_called_with_bad_pointer' hppa-linux-ld: (.text+0x354): undefined reference to `__cmpxchg_called_with_bad_pointer' Add support for cmpxchg on u8 pointers. [1] https://lore.kernel.org/patchwork/patch/1272617/#1468946 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Liam Beguin <liambeguin@gmail.com> Tested-by: Dave Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015c5d5 ] According to the report of [1], this driver is possible to cause the following error in ravb_tx_timeout_work(). ravb e6800000.ethernet ethernet: failed to switch device to config mode This error means that the hardware could not change the state from "Operation" to "Configuration" while some tx and/or rx queue are operating. After that, ravb_config() in ravb_dmac_init() will fail, and then any descriptors will be not allocaled anymore so that NULL pointer dereference happens after that on ravb_start_xmit(). To fix the issue, the ravb_tx_timeout_work() should check the return values of ravb_stop_dma() and ravb_dmac_init(). If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX and just exits. If ravb_dmac_init() fails, just exits. [1] https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/ Reported-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0db9254 ] This reverts commit d358def. There are two issues with "i2c: cadence: Fix the hold bit setting" commit. 1. In case of combined message request from user space, when the HOLD bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent on the bus even before the last message is started. This is because when the HOLD bit is cleared, the FIFOS are empty and there is no pending transfer. The STOP condition should occur only after the last message is completed. 2. The code added by the commit is redundant. Driver is handling the setting/clearing of HOLD bit in right way before the commit. The setting of HOLD bit based on 'bus_hold_flag' is taken care in cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv functions. The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and cdns_i2c_recv functions based on bus_hold_flag and byte count. Since clearing of HOLD bit is done after the slave address is written to the register (writing to address register triggers the message transfer), it is ensured that STOP condition occurs at the right time after completion of the pending transfer (last message). Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 372a8ea ] The ORC unwinder fails to unwind newly forked tasks which haven't yet run on the CPU. It correctly reads the 'ret_from_fork' instruction pointer from the stack, but it incorrectly interprets that value as a call stack address rather than a "signal" one, so the address gets incorrectly decremented in the call to orc_find(), resulting in bad ORC data. Fix it by forcing 'ret_from_fork' frames to be signal frames. Reported-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Link: https://lkml.kernel.org/r/f91a8778dde8aae7f71884b5df2b16d552040441.1594994374.git.jpoimboe@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 039a7a3 ] If a user task's stack is empty, or if it only has user regs, ORC reports it as a reliable empty stack. But arch_stack_walk_reliable() incorrectly treats it as unreliable. That happens because the only success path for user tasks is inside the loop, which only iterates on non-empty stacks. Generally, a user task must end in a user regs frame, but an empty stack is an exception to that rule. Thanks to commit 71c9582 ("x86/unwind/orc: Fix error handling in __unwind_start()"), unwind_start() now sets state->error appropriately. So now for both ORC and FP unwinders, unwind_done() and !unwind_error() always means the end of the stack was successfully reached. So the success path for kthreads is no longer needed -- it can also be used for empty user tasks. Reported-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Link: https://lkml.kernel.org/r/f136a4e5f019219cbc4f4da33b30c2f44fa65b84.1594994374.git.jpoimboe@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6827d1 ] In the implementation of uld_send(), the skb is consumed on all execution paths except one. Release skb when returning NET_XMIT_DROP. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2c6331 ] There's a potential race in xennet_remove(); this is what the driver is doing upon unregistering a network device: 1. state = read bus state 2. if state is not "Closed": 3. request to set state to "Closing" 4. wait for state to be set to "Closing" 5. request to set state to "Closed" 6. wait for state to be set to "Closed" If the state changes to "Closed" immediately after step 1 we are stuck forever in step 4, because the state will never go back from "Closed" to "Closing". Make sure to check also for state == "Closed" in step 4 to prevent the deadlock. Also add a 5 sec timeout any time we wait for the bus state to change, to avoid getting stuck forever in wait_event(). Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0d8aae ] Currently, maximum number of mapper pages are set to the pfn calculated from the memblock size of the memblock containing kernel. This will work until that memblock spans the entire memory. However, it will be set to a wrong value if there are multiple memblocks defined in kernel (e.g. with efi runtime services). Set the the maximum value to the pfn calculated from dram size. Signed-off-by: Atish Patra <atish.patra@wdc.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8754e13 ] This patch fixed 2 issues with the usage of skb_cow in LAPB drivers "lapbether" and "hdlc_x25": 1) After skb_cow fails, kfree_skb should be called to drop a reference to the skb. But in both drivers, kfree_skb is not called. 2) skb_cow should be called before skb_push so that is can ensure the safety of skb_push. But in "lapbether", it is incorrectly called after skb_push. More details about these 2 issues: 1) The behavior of calling kfree_skb on failure is also the behavior of netif_rx, which is called by this function with "return netif_rx(skb);". So this function should follow this behavior, too. 2) In "lapbether", skb_cow is called after skb_push. This results in 2 logical issues: a) skb_push is not protected by skb_cow; b) An extra headroom of 1 byte is ensured after skb_push. This extra headroom has no use in this function. It also has no use in the upper-layer function that this function passes the skb to (x25_lapb_receive_frame in net/x25/x25_dev.c). So logically skb_cow should instead be called before skb_push. Cc: Eric Dumazet <edumazet@google.com> Cc: Martin Schiller <ms@dev.tdt.de> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b757b47 upstream. If a stage-2 page-table contains an executable, read-only mapping at the pte level (e.g. due to dirty logging being enabled), a subsequent write fault to the same page which tries to install a larger block mapping (e.g. due to dirty logging having been disabled) will erroneously inherit the exec permission and consequently skip I-cache invalidation for the rest of the block. Ensure that exec permission is only inherited by write faults when the new mapping is of the same size as the existing one. A subsequent instruction abort will result in I-cache invalidation for the entire block mapping. Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Tested-by: Quentin Perret <qperret@google.com> Reviewed-by: Quentin Perret <qperret@google.com> Cc: Marc Zyngier <maz@kernel.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200723101714.15873-1-will@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…disabled commit d2286ba upstream. Prevent setting the tscdeadline timer if the lapic is hw disabled. Fixes: bce87cc (KVM: x86: consolidate different ways to test for in-kernel LAPIC) Cc: <stable@vger.kernel.org> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Message-Id: <1596165141-28874-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd6558 upstream. 0day reported a possible circular locking dependency: Chain exists of: &irq_desc_lock_class --> console_owner --> &port_lock_key Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&port_lock_key); lock(console_owner); lock(&port_lock_key); lock(&irq_desc_lock_class); The reason for this is a printk() in the i8259 interrupt chip driver which is invoked with the irq descriptor lock held, which reverses the lock operations vs. printk() from arbitrary contexts. Switch the printk() to printk_deferred() to avoid that. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/87365abt2v.fsf@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cff20b3 upstream. To fix the build with newer gccs, that without this patch exit with: LD /tmp/build/perf/tests/perf-in.o ld: /tmp/build/perf/tests/bp_account.o:/git/perf/tools/perf/tests/bp_account.c:22: multiple definition of `the_var'; /tmp/build/perf/tests/bp_signal.o:/git/perf/tools/perf/tests/bp_signal.c:38: first defined here make[4]: *** [/git/perf/tools/build/Makefile.build:145: /tmp/build/perf/tests/perf-in.o] Error 1 First noticed in fedora:rawhide/32 with: [perfbuilder@a5ff49d6e6e4 ~]$ gcc --version gcc (GCC) 10.0.1 20200216 (Red Hat 10.0.1-0.8) Reported-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebcb946 upstream. It is possible to return a pointer to a local variable when looking up the architecture name for the running system and no normalization is done on that value, i.e. we may end up returning the uts.machine local variable. While this doesn't happen on most arches, as normalization takes place, lets fix this by making that a static variable and optimize it a bit by not always running uname(), only the first time. Noticed in fedora rawhide running with: [perfbuilder@a5ff49d6e6e4 ~]$ gcc --version gcc (GCC) 10.0.1 20200216 (Red Hat 10.0.1-0.8) Reported-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d9b04 upstream. Noticed with gcc 10 (fedora rawhide) that those variables were not being declared as static, so end up with: ld: /tmp/build/perf/bench/epoll-wait.o:/git/perf/tools/perf/bench/epoll-wait.c:93: multiple definition of `end'; /tmp/build/perf/bench/futex-hash.o:/git/perf/tools/perf/bench/futex-hash.c:40: first defined here ld: /tmp/build/perf/bench/epoll-wait.o:/git/perf/tools/perf/bench/epoll-wait.c:93: multiple definition of `start'; /tmp/build/perf/bench/futex-hash.o:/git/perf/tools/perf/bench/futex-hash.c:40: first defined here ld: /tmp/build/perf/bench/epoll-wait.o:/git/perf/tools/perf/bench/epoll-wait.c:93: multiple definition of `runtime'; /tmp/build/perf/bench/futex-hash.o:/git/perf/tools/perf/bench/futex-hash.c:40: first defined here ld: /tmp/build/perf/bench/epoll-ctl.o:/git/perf/tools/perf/bench/epoll-ctl.c:38: multiple definition of `end'; /tmp/build/perf/bench/futex-hash.o:/git/perf/tools/perf/bench/futex-hash.c:40: first defined here ld: /tmp/build/perf/bench/epoll-ctl.o:/git/perf/tools/perf/bench/epoll-ctl.c:38: multiple definition of `start'; /tmp/build/perf/bench/futex-hash.o:/git/perf/tools/perf/bench/futex-hash.c:40: first defined here ld: /tmp/build/perf/bench/epoll-ctl.o:/git/perf/tools/perf/bench/epoll-ctl.c:38: multiple definition of `runtime'; /tmp/build/perf/bench/futex-hash.o:/git/perf/tools/perf/bench/futex-hash.c:40: first defined here make[4]: *** [/git/perf/tools/build/Makefile.build:145: /tmp/build/perf/bench/perf-in.o] Error 1 Prefix those with bench__ and add them to bench/bench.h, so that we can share those on the tools needing to access those variables from signal handlers. Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lore.kernel.org/lkml/20200303155811.GD13702@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the 5.4.56 stable release Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
zandrey
pushed a commit
to zandrey/linux-fslc
that referenced
this pull request
Apr 6, 2021
commit 92063f3 upstream. The kernel may be built with multiple LSMs, but only a subset may be enabled on the boot command line by specifying "lsm=". Not including "integrity" on the ordered LSM list may result in a NULL deref. As reported by Dmitry Vyukov: in qemu: qemu-system-x86_64 -enable-kvm -machine q35,nvdimm -cpu max,migratable=off -smp 4 -m 4G,slots=4,maxmem=16G -hda wheezy.img -kernel arch/x86/boot/bzImage -nographic -vga std -soundhw all -usb -usbdevice tablet -bt hci -bt device:keyboard -net user,host=10.0.2.10,hostfwd=tcp::10022-:22 -net nic,model=virtio-net-pci -object memory-backend-file,id=pmem1,share=off,mem-path=/dev/zero,size=64M -device nvdimm,id=nvdimm1,memdev=pmem1 -append "console=ttyS0 root=/dev/sda earlyprintk=serial rodata=n oops=panic panic_on_warn=1 panic=86400 lsm=smack numa=fake=2 nopcid dummy_hcd.num=8" -pidfile vm_pid -m 2G -cpu host But it crashes on NULL deref in integrity_inode_get during boot: Run /sbin/init as init process BUG: kernel NULL pointer dereference, address: 000000000000001c PGD 0 P4D 0 Oops: 0000 [Freescale#1] PREEMPT SMP KASAN CPU: 3 PID: 1 Comm: swapper/0 Not tainted 5.12.0-rc2+ Freescale#97 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-44-g88ab0c15525c-prebuilt.qemu.org 04/01/2014 RIP: 0010:kmem_cache_alloc+0x2b/0x370 mm/slub.c:2920 Code: 57 41 56 41 55 41 54 41 89 f4 55 48 89 fd 53 48 83 ec 10 44 8b 3d d9 1f 90 0b 65 48 8b 04 25 28 00 00 00 48 89 44 24 08 31 c0 <8b> 5f 1c 4cf RSP: 0000:ffffc9000032f9d8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888017fc4f00 RCX: 0000000000000000 RDX: ffff888040220000 RSI: 0000000000000c40 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: ffff888019263627 R10: ffffffff83937cd1 R11: 0000000000000000 R12: 0000000000000c40 R13: ffff888019263538 R14: 0000000000000000 R15: 0000000000ffffff FS: 0000000000000000(0000) GS:ffff88802d180000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000001c CR3: 000000000b48e000 CR4: 0000000000750ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: integrity_inode_get+0x47/0x260 security/integrity/iint.c:105 process_measurement+0x33d/0x17e0 security/integrity/ima/ima_main.c:237 ima_bprm_check+0xde/0x210 security/integrity/ima/ima_main.c:474 security_bprm_check+0x7d/0xa0 security/security.c:845 search_binary_handler fs/exec.c:1708 [inline] exec_binprm fs/exec.c:1761 [inline] bprm_execve fs/exec.c:1830 [inline] bprm_execve+0x764/0x19a0 fs/exec.c:1792 kernel_execve+0x370/0x460 fs/exec.c:1973 try_to_run_init_process+0x14/0x4e init/main.c:1366 kernel_init+0x11d/0x1b8 init/main.c:1477 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:294 Modules linked in: CR2: 000000000000001c ---[ end trace 22d601a500de7d79 ]--- Since LSMs and IMA may be configured at build time, but not enabled at run time, panic the system if "integrity" was not initialized before use. Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: 79f7865 ("LSM: Introduce "lsm=" for boottime LSM selection") Cc: stable@vger.kernel.org Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zandrey
pushed a commit
to zandrey/linux-fslc
that referenced
this pull request
Apr 6, 2021
commit 92063f3 upstream. The kernel may be built with multiple LSMs, but only a subset may be enabled on the boot command line by specifying "lsm=". Not including "integrity" on the ordered LSM list may result in a NULL deref. As reported by Dmitry Vyukov: in qemu: qemu-system-x86_64 -enable-kvm -machine q35,nvdimm -cpu max,migratable=off -smp 4 -m 4G,slots=4,maxmem=16G -hda wheezy.img -kernel arch/x86/boot/bzImage -nographic -vga std -soundhw all -usb -usbdevice tablet -bt hci -bt device:keyboard -net user,host=10.0.2.10,hostfwd=tcp::10022-:22 -net nic,model=virtio-net-pci -object memory-backend-file,id=pmem1,share=off,mem-path=/dev/zero,size=64M -device nvdimm,id=nvdimm1,memdev=pmem1 -append "console=ttyS0 root=/dev/sda earlyprintk=serial rodata=n oops=panic panic_on_warn=1 panic=86400 lsm=smack numa=fake=2 nopcid dummy_hcd.num=8" -pidfile vm_pid -m 2G -cpu host But it crashes on NULL deref in integrity_inode_get during boot: Run /sbin/init as init process BUG: kernel NULL pointer dereference, address: 000000000000001c PGD 0 P4D 0 Oops: 0000 [Freescale#1] PREEMPT SMP KASAN CPU: 3 PID: 1 Comm: swapper/0 Not tainted 5.12.0-rc2+ Freescale#97 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-44-g88ab0c15525c-prebuilt.qemu.org 04/01/2014 RIP: 0010:kmem_cache_alloc+0x2b/0x370 mm/slub.c:2920 Code: 57 41 56 41 55 41 54 41 89 f4 55 48 89 fd 53 48 83 ec 10 44 8b 3d d9 1f 90 0b 65 48 8b 04 25 28 00 00 00 48 89 44 24 08 31 c0 <8b> 5f 1c 4cf RSP: 0000:ffffc9000032f9d8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888017fc4f00 RCX: 0000000000000000 RDX: ffff888040220000 RSI: 0000000000000c40 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: ffff888019263627 R10: ffffffff83937cd1 R11: 0000000000000000 R12: 0000000000000c40 R13: ffff888019263538 R14: 0000000000000000 R15: 0000000000ffffff FS: 0000000000000000(0000) GS:ffff88802d180000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000001c CR3: 000000000b48e000 CR4: 0000000000750ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: integrity_inode_get+0x47/0x260 security/integrity/iint.c:105 process_measurement+0x33d/0x17e0 security/integrity/ima/ima_main.c:237 ima_bprm_check+0xde/0x210 security/integrity/ima/ima_main.c:474 security_bprm_check+0x7d/0xa0 security/security.c:845 search_binary_handler fs/exec.c:1708 [inline] exec_binprm fs/exec.c:1761 [inline] bprm_execve fs/exec.c:1830 [inline] bprm_execve+0x764/0x19a0 fs/exec.c:1792 kernel_execve+0x370/0x460 fs/exec.c:1973 try_to_run_init_process+0x14/0x4e init/main.c:1366 kernel_init+0x11d/0x1b8 init/main.c:1477 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:294 Modules linked in: CR2: 000000000000001c ---[ end trace 22d601a500de7d79 ]--- Since LSMs and IMA may be configured at build time, but not enabled at run time, panic the system if "integrity" was not initialized before use. Reported-by: Dmitry Vyukov <dvyukov@google.com> Fixes: 79f7865 ("LSM: Introduce "lsm=" for boottime LSM selection") Cc: stable@vger.kernel.org Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zandrey
pushed a commit
to zandrey/linux-fslc
that referenced
this pull request
Jun 14, 2022
commit ba3beec upstream. Fix a crash that happens if an Rx only socket is created first, then a second socket is created that is Tx only and bound to the same umem as the first socket and also the same netdev and queue_id together with the XDP_SHARED_UMEM flag. In this specific case, the tx_descs array page pool was not created by the first socket as it was an Rx only socket. When the second socket is bound it needs this tx_descs array of this shared page pool as it has a Tx component, but unfortunately it was never allocated, leading to a crash. Note that this array is only used for zero-copy drivers using the batched Tx APIs, currently only ice and i40e. [ 5511.150360] BUG: kernel NULL pointer dereference, address: 0000000000000008 [ 5511.158419] #PF: supervisor write access in kernel mode [ 5511.164472] #PF: error_code(0x0002) - not-present page [ 5511.170416] PGD 0 P4D 0 [ 5511.173347] Oops: 0002 [Freescale#1] PREEMPT SMP PTI [ 5511.178186] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G E 5.18.0-rc1+ Freescale#97 [ 5511.187245] Hardware name: Intel Corp. GRANTLEY/GRANTLEY, BIOS GRRFCRB1.86B.0276.D07.1605190235 05/19/2016 [ 5511.198418] RIP: 0010:xsk_tx_peek_release_desc_batch+0x198/0x310 [ 5511.205375] Code: c0 83 c6 01 84 c2 74 6d 8d 46 ff 23 07 44 89 e1 48 83 c0 14 48 c1 e1 04 48 c1 e0 04 48 03 47 10 4c 01 c1 48 8b 50 08 48 8b 00 <48> 89 51 08 48 89 01 41 80 bd d7 00 00 00 00 75 82 48 8b 19 49 8b [ 5511.227091] RSP: 0018:ffffc90000003dd0 EFLAGS: 00010246 [ 5511.233135] RAX: 0000000000000000 RBX: ffff88810c8da600 RCX: 0000000000000000 [ 5511.241384] RDX: 000000000000003c RSI: 0000000000000001 RDI: ffff888115f555c0 [ 5511.249634] RBP: ffffc90000003e08 R08: 0000000000000000 R09: ffff889092296b48 [ 5511.257886] R10: 0000ffffffffffff R11: ffff889092296800 R12: 0000000000000000 [ 5511.266138] R13: ffff88810c8db500 R14: 0000000000000040 R15: 0000000000000100 [ 5511.274387] FS: 0000000000000000(0000) GS:ffff88903f800000(0000) knlGS:0000000000000000 [ 5511.283746] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5511.290389] CR2: 0000000000000008 CR3: 00000001046e2001 CR4: 00000000003706f0 [ 5511.298640] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 5511.306892] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 5511.315142] Call Trace: [ 5511.317972] <IRQ> [ 5511.320301] ice_xmit_zc+0x68/0x2f0 [ice] [ 5511.324977] ? ktime_get+0x38/0xa0 [ 5511.328913] ice_napi_poll+0x7a/0x6a0 [ice] [ 5511.333784] __napi_poll+0x2c/0x160 [ 5511.337821] net_rx_action+0xdd/0x200 [ 5511.342058] __do_softirq+0xe6/0x2dd [ 5511.346198] irq_exit_rcu+0xb5/0x100 [ 5511.350339] common_interrupt+0xa4/0xc0 [ 5511.354777] </IRQ> [ 5511.357201] <TASK> [ 5511.359625] asm_common_interrupt+0x1e/0x40 [ 5511.364466] RIP: 0010:cpuidle_enter_state+0xd2/0x360 [ 5511.370211] Code: 49 89 c5 0f 1f 44 00 00 31 ff e8 e9 00 7b ff 45 84 ff 74 12 9c 58 f6 c4 02 0f 85 72 02 00 00 31 ff e8 02 0c 80 ff fb 45 85 f6 <0f> 88 11 01 00 00 49 63 c6 4c 2b 2c 24 48 8d 14 40 48 8d 14 90 49 [ 5511.391921] RSP: 0018:ffffffff82a03e60 EFLAGS: 00000202 [ 5511.397962] RAX: ffff88903f800000 RBX: 0000000000000001 RCX: 000000000000001f [ 5511.406214] RDX: 0000000000000000 RSI: ffffffff823400b9 RDI: ffffffff8234c046 [ 5511.424646] RBP: ffff88810a384800 R08: 000005032a28c046 R09: 0000000000000008 [ 5511.443233] R10: 000000000000000b R11: 0000000000000006 R12: ffffffff82bcf700 [ 5511.461922] R13: 000005032a28c046 R14: 0000000000000001 R15: 0000000000000000 [ 5511.480300] cpuidle_enter+0x29/0x40 [ 5511.494329] do_idle+0x1c7/0x250 [ 5511.507610] cpu_startup_entry+0x19/0x20 [ 5511.521394] start_kernel+0x649/0x66e [ 5511.534626] secondary_startup_64_no_verify+0xc3/0xcb [ 5511.549230] </TASK> Detect such case during bind() and allocate this memory region via newly introduced xp_alloc_tx_descs(). Also, use kvcalloc instead of kcalloc as for other buffer pool allocations, so that it matches the kvfree() from xp_destroy(). Fixes: d1bc532 ("i40e: xsk: Move tmp desc array from driver to pool") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20220425153745.481322-1-maciej.fijalkowski@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
20 participants
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
Automatic merge performed, no conflicts reported.
-- andrey