USB: pl2303: fix baud-rate divisor calculations

This commit fixes the following issues:

1. The 9th bit of buf was believed to be the LSB of divisor's
exponent, but the hardware interprets it as MSB (9th bit) of the
mantissa. The exponent is actually one bit shorter and applies
to base 4, not 2 as previously believed.

2. Loop iterations doubled the exponent instead of incrementing.

3. The exponent wasn't checked for overflow.

4. The function returned requested rate instead of actual rate.

Due to issue SolidRun#2, the old code deviated from the wrong formula
described in SolidRun#1 and actually yielded correct rates when divisor
was lower than 4096 by using exponents of 0, 2 or 4 base-2,
interpreted as 0, 1, 2 base-4 with the 9th mantissa bit clear.
However, at 93.75 kbaud or less the rate turned out too slow
due to SolidRun#2 or too fast due to SolidRun#2 and SolidRun#3.

I tested this patch by sending and validating 0x00,0x01,..,0xff
to an FTDI dongle at 234, 987, 2401, 9601, 31415, 115199, 250k,
500k, 750k, 1M, 1.5M, 3M+1 baud. All rates passed.

I also used pv to check speed at some rates unsupported by FTDI:
45 (the lowest possible), 2M, 4M, 5M and 6M-1. Looked sane.

Signed-off-by: Michal Pecio <[email protected]>
Fixes: 399aa9a ("USB: pl2303: use divisors for unsupported baud
rates")
Cc: stable <[email protected]> # v3.18
[johan: update summary ]
Signed-off-by: Johan Hovold <[email protected]>

Author: Michał Pecio

drivers/usb/serial/pl2303.c

@@ -362,21 +362,38 @@ static speed_t pl2303_encode_baud_rate_direct(unsigned char buf[4],
 static speed_t pl2303_encode_baud_rate_divisor(unsigned char buf[4],
 								speed_t baud)
 {
-	unsigned int tmp;
+	unsigned int baseline, mantissa, exponent;
 
 	/*
 	 * Apparently the formula is:
-	 * baudrate = 12M * 32 / (2^buf[1]) / buf[0]
+	 *   baudrate = 12M * 32 / (mantissa * 4^exponent)
+	 * where
+	 *   mantissa = buf[8:0]
+	 *   exponent = buf[11:9]
 	 */
-	tmp = 12000000 * 32 / baud;
+	baseline = 12000000 * 32;
+	mantissa = baseline / baud;
+	if (mantissa == 0)
+		mantissa = 1;	/* Avoid dividing by zero if baud > 32*12M. */
+	exponent = 0;
+	while (mantissa >= 512) {
+		if (exponent < 7) {
+			mantissa >>= 2;	/* divide by 4 */
+			exponent++;
+		} else {
+			/* Exponent is maxed. Trim mantissa and leave. */
+			mantissa = 511;
+			break;
+		}
+	}
+
 	buf[3] = 0x80;
 	buf[2] = 0;
-	buf[1] = (tmp >= 256);
-	while (tmp >= 256) {
-		tmp >>= 2;
-		buf[1] <<= 1;
-	}
-	buf[0] = tmp;
+	buf[1] = exponent << 1 | mantissa >> 8;
+	buf[0] = mantissa & 0xff;
+
+	/* Calculate and return the exact baud rate. */
+	baud = (baseline / mantissa) >> (exponent << 1);
 
 	return baud;
 }