media: i2c: imx214: Fix link frequency validation

[ Upstream commit acc2945 ]

The driver defines IMX214_DEFAULT_LINK_FREQ 480000000, and then
IMX214_DEFAULT_PIXEL_RATE ((IMX214_DEFAULT_LINK_FREQ * 8LL) / 10),
which works out as 384MPix/s. (The 8 is 4 lanes and DDR.)

Parsing the PLL registers with the defined 24MHz input. We're in single
PLL mode, so MIPI frequency is directly linked to pixel rate.  VTCK ends
up being 1200MHz, and VTPXCK and OPPXCK both are 120MHz.  Section 5.3
"Frame rate calculation formula" says "Pixel rate
[pixels/s] = VTPXCK [MHz] * 4", so 120 * 4 = 480MPix/s, which basically
agrees with my number above.

3.1.4. MIPI global timing setting says "Output bitrate = OPPXCK * reg
0x113[7:0]", so 120MHz * 10, or 1200Mbit/s. That would be a link
frequency of 600MHz due to DDR.
That also matches to 480MPix/s * 10bpp / 4 lanes / 2 for DDR.

Keep the previous link frequency for backward compatibility.

Acked-by: Ricardo Ribalda <[email protected]>
Signed-off-by: André Apitzsch <[email protected]>
Fixes: 4361905 ("media: imx214: Add imx214 camera sensor driver")
Cc: [email protected]
Signed-off-by: Sakari Ailus <[email protected]>
Signed-off-by: Hans Verkuil <[email protected]>
[ changed dev_err() to dev_err_probe() for the final error case ]
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

Author: André Apitzsch

drivers/media/i2c/imx214.c

@@ -20,7 +20,9 @@
 #include <media/v4l2-subdev.h>
 
 #define IMX214_DEFAULT_CLK_FREQ	24000000
-#define IMX214_DEFAULT_LINK_FREQ 480000000
+#define IMX214_DEFAULT_LINK_FREQ	600000000
+/* Keep wrong link frequency for backward compatibility */
+#define IMX214_DEFAULT_LINK_FREQ_LEGACY	480000000
 #define IMX214_DEFAULT_PIXEL_RATE ((IMX214_DEFAULT_LINK_FREQ * 8LL) / 10)
 #define IMX214_FPS 30
 #define IMX214_MBUS_CODE MEDIA_BUS_FMT_SRGGB10_1X10
@@ -892,17 +894,26 @@ static int imx214_parse_fwnode(struct device *dev)
 		goto done;
 	}
 
-	for (i = 0; i < bus_cfg.nr_of_link_frequencies; i++)
+	if (bus_cfg.nr_of_link_frequencies != 1)
+		dev_warn(dev, "Only one link-frequency supported, please review your DT. Continuing anyway\n");
+
+	for (i = 0; i < bus_cfg.nr_of_link_frequencies; i++) {
 		if (bus_cfg.link_frequencies[i] == IMX214_DEFAULT_LINK_FREQ)
 			break;
-
-	if (i == bus_cfg.nr_of_link_frequencies) {
-		dev_err(dev, "link-frequencies %d not supported, Please review your DT\n",
-			IMX214_DEFAULT_LINK_FREQ);
-		ret = -EINVAL;
-		goto done;
+		if (bus_cfg.link_frequencies[i] ==
+		    IMX214_DEFAULT_LINK_FREQ_LEGACY) {
+			dev_warn(dev,
+				 "link-frequencies %d not supported, please review your DT. Continuing anyway\n",
+				 IMX214_DEFAULT_LINK_FREQ);
+			break;
+		}
 	}
 
+	if (i == bus_cfg.nr_of_link_frequencies)
+		ret = dev_err_probe(dev, -EINVAL,
+				    "link-frequencies %d not supported, please review your DT\n",
+				    IMX214_DEFAULT_LINK_FREQ);
+
 done:
 	v4l2_fwnode_endpoint_free(&bus_cfg);
 	fwnode_handle_put(endpoint);