Merge branch 'phy-motorcomm-driver-strength'

Samin Guo says:

====================
Add motorcomm phy pad-driver-strength-cfg support

The motorcomm phy (YT8531) supports the ability to adjust the drive
strength of the rx_clk/rx_data, and the default strength may not be
suitable for all boards. So add configurable options to better match
the boards.(e.g. StarFive VisionFive 2)

The first patch adds a description of dt-bingding, and the second patch adds
YT8531's parsing and settings for pad-driver-strength-cfg.

Changes since v4:
Patch 1:
- Removed register-related DS(3b) values and added vol descriptions (by Andrew Lunn)
- Dropped the type and added '-microamp' suffix. (by Rob Herring)
Patch 2:
- Return -EINVAL if the value in DT but it is invalid (by Andrew Lunn)

Changes since v3:
Patch 1:
- Used current values instead of register values
- Added units and numerical descriptions of driver-strength
Patch 2:
- Added a lookup table to listing the valid values in the schema (by Andrew Lunn)

Changes since v2:
Patch 2:
- Readjusted the order of YT8531_RGMII_xxx to below YTPHY_PAD_DRIVE_STRENGTH_REG (by Frank Sae)
- Reversed Christmas tree, sort these longest first, shortest last (by Andrew Lunn)
- Rebased on tag v6.4

Changes since v1:
Patch 1:
- Renamed "rx-xxx-driver-strength" to "motorcomm,rx-xxx-driver-strength" (by Frank Sae)
Patch 2:
- Added default values for rxc/rxd driver strength (by Frank Sea/Andrew Lunn)
- Added range checking when val is in DT (by Frank Sea/Andrew Lunn)

Previous versions:
v1 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]
v2 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]
v3 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]
v4 - https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]
====================

Signed-off-by: David S. Miller <[email protected]>

Author: davem330

Documentation/devicetree/bindings/net/motorcomm,yt8xxx.yaml

@@ -52,6 +52,40 @@ properties:
       for a timer.
     type: boolean
 
+  motorcomm,rx-clk-drv-microamp:
+    description: |
+      drive strength of rx_clk rgmii pad.
+      The YT8531 RGMII LDO voltage supports 1.8V/3.3V, and the LDO voltage can
+      be configured with hardware pull-up resistors to match the SOC voltage
+      (usually 1.8V).
+      The software can read the registers to obtain the LDO voltage and configure
+      the legal drive strength(curren).
+      =====================================================
+      | voltage |        current Available (uA)           |
+      |   1.8v  | 1200 2100 2700 2910 3110 3600 3970 4350 |
+      |   3.3v  | 3070 4080 4370 4680 5020 5450 5740 6140 |
+      =====================================================
+    enum: [ 1200, 2100, 2700, 2910, 3070, 3110, 3600, 3970,
+            4080, 4350, 4370, 4680, 5020, 5450, 5740, 6140 ]
+    default: 2910
+
+  motorcomm,rx-data-drv-microamp:
+    description: |
+      drive strength of rx_data/rx_ctl rgmii pad.
+      The YT8531 RGMII LDO voltage supports 1.8V/3.3V, and the LDO voltage can
+      be configured with hardware pull-up resistors to match the SOC voltage
+      (usually 1.8V).
+      The software can read the registers to obtain the LDO voltage and configure
+      the legal drive strength(curren).
+      =====================================================
+      | voltage |        current Available (uA)           |
+      |   1.8v  | 1200 2100 2700 2910 3110 3600 3970 4350 |
+      |   3.3v  | 3070 4080 4370 4680 5020 5450 5740 6140 |
+      =====================================================
+    enum: [ 1200, 2100, 2700, 2910, 3070, 3110, 3600, 3970,
+            4080, 4350, 4370, 4680, 5020, 5450, 5740, 6140 ]
+    default: 2910
+
   motorcomm,tx-clk-adj-enabled:
     description: |
       This configuration is mainly to adapt to VF2 with JH7110 SoC.

drivers/net/phy/motorcomm.c

@@ -163,6 +163,10 @@
 
 #define YT8521_CHIP_CONFIG_REG			0xA001
 #define YT8521_CCR_SW_RST			BIT(15)
+#define YT8531_RGMII_LDO_VOL_MASK		GENMASK(5, 4)
+#define YT8531_LDO_VOL_3V3			0x0
+#define YT8531_LDO_VOL_1V8			0x2
+
 /* 1b0 disable 1.9ns rxc clock delay  *default*
  * 1b1 enable 1.9ns rxc clock delay
  */
@@ -236,6 +240,12 @@
  */
 #define YTPHY_WCR_TYPE_PULSE			BIT(0)
 
+#define YTPHY_PAD_DRIVE_STRENGTH_REG		0xA010
+#define YT8531_RGMII_RXC_DS_MASK		GENMASK(15, 13)
+#define YT8531_RGMII_RXD_DS_HI_MASK		BIT(12)		/* Bit 2 of rxd_ds */
+#define YT8531_RGMII_RXD_DS_LOW_MASK		GENMASK(5, 4)	/* Bit 1/0 of rxd_ds */
+#define YT8531_RGMII_RX_DS_DEFAULT		0x3
+
 #define YTPHY_SYNCE_CFG_REG			0xA012
 #define YT8521_SCR_SYNCE_ENABLE			BIT(5)
 /* 1b0 output 25m clock
@@ -834,6 +844,110 @@ static int ytphy_rgmii_clk_delay_config_with_lock(struct phy_device *phydev)
 	return ret;
 }
 
+/**
+ * struct ytphy_ldo_vol_map - map a current value to a register value
+ * @vol: ldo voltage
+ * @ds:  value in the register
+ * @cur: value in device configuration
+ */
+struct ytphy_ldo_vol_map {
+	u32 vol;
+	u32 ds;
+	u32 cur;
+};
+
+static const struct ytphy_ldo_vol_map yt8531_ldo_vol[] = {
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 0, .cur = 1200},
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 1, .cur = 2100},
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 2, .cur = 2700},
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 3, .cur = 2910},
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 4, .cur = 3110},
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 5, .cur = 3600},
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 6, .cur = 3970},
+	{.vol = YT8531_LDO_VOL_1V8, .ds = 7, .cur = 4350},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 0, .cur = 3070},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 1, .cur = 4080},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 2, .cur = 4370},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 3, .cur = 4680},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 4, .cur = 5020},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 5, .cur = 5450},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 6, .cur = 5740},
+	{.vol = YT8531_LDO_VOL_3V3, .ds = 7, .cur = 6140},
+};
+
+static u32 yt8531_get_ldo_vol(struct phy_device *phydev)
+{
+	u32 val;
+
+	val = ytphy_read_ext_with_lock(phydev, YT8521_CHIP_CONFIG_REG);
+	val = FIELD_GET(YT8531_RGMII_LDO_VOL_MASK, val);
+
+	return val <= YT8531_LDO_VOL_1V8 ? val : YT8531_LDO_VOL_1V8;
+}
+
+static int yt8531_get_ds_map(struct phy_device *phydev, u32 cur)
+{
+	u32 vol;
+	int i;
+
+	vol = yt8531_get_ldo_vol(phydev);
+	for (i = 0; i < ARRAY_SIZE(yt8531_ldo_vol); i++) {
+		if (yt8531_ldo_vol[i].vol == vol && yt8531_ldo_vol[i].cur == cur)
+			return yt8531_ldo_vol[i].ds;
+	}
+
+	return -EINVAL;
+}
+
+static int yt8531_set_ds(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	u32 ds_field_low, ds_field_hi, val;
+	int ret, ds;
+
+	/* set rgmii rx clk driver strength */
+	if (!of_property_read_u32(node, "motorcomm,rx-clk-drv-microamp", &val)) {
+		ds = yt8531_get_ds_map(phydev, val);
+		if (ds < 0)
+			return dev_err_probe(&phydev->mdio.dev, ds,
+					     "No matching current value was found.\n");
+	} else {
+		ds = YT8531_RGMII_RX_DS_DEFAULT;
+	}
+
+	ret = ytphy_modify_ext_with_lock(phydev,
+					 YTPHY_PAD_DRIVE_STRENGTH_REG,
+					 YT8531_RGMII_RXC_DS_MASK,
+					 FIELD_PREP(YT8531_RGMII_RXC_DS_MASK, ds));
+	if (ret < 0)
+		return ret;
+
+	/* set rgmii rx data driver strength */
+	if (!of_property_read_u32(node, "motorcomm,rx-data-drv-microamp", &val)) {
+		ds = yt8531_get_ds_map(phydev, val);
+		if (ds < 0)
+			return dev_err_probe(&phydev->mdio.dev, ds,
+					     "No matching current value was found.\n");
+	} else {
+		ds = YT8531_RGMII_RX_DS_DEFAULT;
+	}
+
+	ds_field_hi = FIELD_GET(BIT(2), ds);
+	ds_field_hi = FIELD_PREP(YT8531_RGMII_RXD_DS_HI_MASK, ds_field_hi);
+
+	ds_field_low = FIELD_GET(GENMASK(1, 0), ds);
+	ds_field_low = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW_MASK, ds_field_low);
+
+	ret = ytphy_modify_ext_with_lock(phydev,
+					 YTPHY_PAD_DRIVE_STRENGTH_REG,
+					 YT8531_RGMII_RXD_DS_LOW_MASK | YT8531_RGMII_RXD_DS_HI_MASK,
+					 ds_field_low | ds_field_hi);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
 /**
  * yt8521_probe() - read chip config then set suitable polling_mode
  * @phydev: a pointer to a &struct phy_device
@@ -1518,6 +1632,10 @@ static int yt8531_config_init(struct phy_device *phydev)
 			return ret;
 	}
 
+	ret = yt8531_set_ds(phydev);
+	if (ret < 0)
+		return ret;
+
 	return 0;
 }