♻️ SDSUPPORT => HAS_MEDIA

Author: thinkyhead

Marlin/src/HAL/AVR/HAL.cpp

@@ -145,12 +145,12 @@ void MarlinHAL::reboot() {
 // Free Memory Accessor
 // ------------------------
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
 
   #include "../../sd/SdFatUtil.h"
   int freeMemory() { return SdFatUtil::FreeRam(); }
 
-#else // !SDSUPPORT
+#else // !HAS_MEDIA
 
   extern "C" {
     extern char __bss_end;
@@ -167,6 +167,6 @@ void MarlinHAL::reboot() {
     }
   }
 
-#endif // !SDSUPPORT
+#endif // !HAS_MEDIA
 
 #endif // __AVR__

Marlin/src/HAL/DUE/HAL.cpp

@@ -45,7 +45,7 @@ uint16_t MarlinHAL::adc_result;
 #endif
 
 void MarlinHAL::init() {
-  #if ENABLED(SDSUPPORT)
+  #if HAS_MEDIA
     OUT_WRITE(SDSS, HIGH);  // Try to set SDSS inactive before any other SPI users start up
   #endif
   usb_task_init();          // Initialize the USB stack

Marlin/src/HAL/DUE/inc/SanityCheck.h

@@ -70,7 +70,7 @@
  */
 #define _IS_HW_SPI(P) (defined(TMC_SW_##P) && (TMC_SW_##P == SD_MOSI_PIN || TMC_SW_##P == SD_MISO_PIN || TMC_SW_##P == SD_SCK_PIN))
 
-#if ENABLED(SDSUPPORT) && HAS_DRIVER(TMC2130)
+#if HAS_MEDIA && HAS_DRIVER(TMC2130)
   #if ENABLED(TMC_USE_SW_SPI)
     #if DISABLED(DUE_SOFTWARE_SPI) && (_IS_HW_SPI(MOSI) || _IS_HW_SPI(MISO) || _IS_HW_SPI(SCK))
       #error "DUE hardware SPI is required but is incompatible with TMC2130 software SPI. Either disable TMC_USE_SW_SPI or use separate pins for the two SPIs."

Marlin/src/HAL/DUE/usb/conf_usb.h

@@ -101,7 +101,7 @@
 #define  USB_DEVICE_SPECIFIC_REQUEST()  usb_task_other_requests()
 //@}
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
   /**
    * USB Device low level configuration
    * When only one interface is used, these configurations are defined by the class module.
@@ -185,7 +185,7 @@
 //! Enable id string of interface to add an extra USB string
 #define  UDI_CDC_IAD_STRING_ID            4
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
   /**
    * USB CDC low level configuration
    * In standalone these configurations are defined by the CDC module.

Marlin/src/HAL/DUE/usb/sd_mmc_spi_mem.cpp

@@ -6,7 +6,7 @@
 
 #include "../../../inc/MarlinConfig.h"
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
 
 #include "../../../sd/cardreader.h"
 extern "C" {
@@ -138,5 +138,5 @@ Ctrl_status sd_mmc_spi_usb_write_10(uint32_t addr, uint16_t nb_sector) {
 
 #endif // ACCESS_USB == true
 
-#endif // SDSUPPORT
+#endif // HAS_MEDIA
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/usb/udi_cdc_desc.c

@@ -51,7 +51,7 @@
 #include "udc_desc.h"
 #include "udi_cdc.h"
 
-#if DISABLED(SDSUPPORT)
+#if !HAS_MEDIA
 
 /**
  * \defgroup udi_cdc_group_single_desc USB device descriptors for a single interface
@@ -256,6 +256,6 @@ UDC_DESC_STORAGE udc_config_t udc_config = {
 //@}
 //@}
 
-#endif // SDSUPPORT
+#endif // HAS_MEDIA
 
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/usb/udi_composite_desc.c

@@ -50,7 +50,7 @@
 #include "udd.h"
 #include "udc_desc.h"
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
 
 /**
  * \defgroup udi_group_desc Descriptors for a USB Device
@@ -189,4 +189,4 @@ UDC_DESC_STORAGE udc_config_t udc_config = {
 
 #endif // ARDUINO_ARCH_SAM
 
-#endif // SDSUPPORT
+#endif // HAS_MEDIA

Marlin/src/HAL/DUE/usb/udi_msc.c

@@ -57,7 +57,7 @@
 #include "ctrl_access.h"
 #include <string.h>
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
 
 #ifndef UDI_MSC_NOTIFY_TRANS_EXT
 #  define UDI_MSC_NOTIFY_TRANS_EXT()
@@ -1127,6 +1127,6 @@ bool udi_msc_trans_block(bool b_read, uint8_t * block, iram_size_t block_size,
 
 //@}
 
-#endif // SDSUPPORT
+#endif // HAS_MEDIA
 
 #endif // ARDUINO_ARCH_SAM

Marlin/src/HAL/DUE/usb/usb_task.c

@@ -51,14 +51,14 @@
 #include "conf_usb.h"
 #include "udc.h"
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
   static volatile bool main_b_msc_enable = false;
 #endif
 static volatile bool main_b_cdc_enable = false;
 static volatile bool main_b_dtr_active = false;
 
 void usb_task_idle(void) {
-  #if ENABLED(SDSUPPORT)
+  #if HAS_MEDIA
     // Attend SD card access from the USB MSD -- Prioritize access to improve speed
     int delay = 2;
     while (main_b_msc_enable && --delay > 0) {
@@ -70,7 +70,7 @@ void usb_task_idle(void) {
   #endif
 }
 
-#if ENABLED(SDSUPPORT)
+#if HAS_MEDIA
   bool usb_task_msc_enable(void)                { return ((main_b_msc_enable = true)); }
   void usb_task_msc_disable(void)               { main_b_msc_enable = false; }
   bool usb_task_msc_isenabled(void)             { return main_b_msc_enable; }
@@ -206,13 +206,13 @@ static USB_MicrosoftExtendedPropertiesDescriptor microsoft_extended_properties_d
 bool usb_task_extra_string(void) {
   static uint8_t udi_msft_magic[] = "MSFT100\xEE";
   static uint8_t udi_cdc_name[] = "CDC interface";
-  #if ENABLED(SDSUPPORT)
+  #if HAS_MEDIA
     static uint8_t udi_msc_name[] = "MSC interface";
   #endif
 
   struct extra_strings_desc_t {
     usb_str_desc_t header;
-    #if ENABLED(SDSUPPORT)
+    #if HAS_MEDIA
       le16_t string[Max(Max(sizeof(udi_cdc_name) - 1, sizeof(udi_msc_name) - 1), sizeof(udi_msft_magic) - 1)];
     #else
       le16_t string[Max(sizeof(udi_cdc_name) - 1, sizeof(udi_msft_magic) - 1)];
@@ -231,7 +231,7 @@ bool usb_task_extra_string(void) {
     str_lgt = sizeof(udi_cdc_name) - 1;
     str = udi_cdc_name;
     break;
-  #if ENABLED(SDSUPPORT)
+  #if HAS_MEDIA
     case UDI_MSC_STRING_ID:
       str_lgt = sizeof(udi_msc_name) - 1;
       str = udi_msc_name;

Marlin/src/HAL/ESP32/HAL_SPI.cpp

@@ -53,7 +53,7 @@ static SPISettings spiConfig;
 // ------------------------
 
 void spiBegin() {
-  #if ENABLED(SDSUPPORT) && PIN_EXISTS(SD_SS)
+  #if HAS_MEDIA && PIN_EXISTS(SD_SS)
     OUT_WRITE(SD_SS_PIN, HIGH);
   #endif
 }