pins_RAMPS.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */



#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
  #error "Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif

#ifndef BOARD_NAME
  #define BOARD_NAME "RAMPS 1.4"
#endif

#define LARGE_FLASH true

    #define X_STEP_PIN         54
    #define X_DIR_PIN          55
    #define X_ENABLE_PIN       38
    #define X_MIN_PIN           3
    #define X_MAX_PIN           2 
//#define X_MAX_PIN           -1////此管脚用作Z_TEST

    #define Y_STEP_PIN         60
    #define Y_DIR_PIN          61
    #define Y_ENABLE_PIN       56
//    #define Y_MIN_PIN          14//d14 as uart3 pin
#define Y_MIN_PIN          42
 //   #define Y_MAX_PIN          43
    #define Y_MAX_PIN         -1   // 15 d15 as uart3 pin

    #define Z_STEP_PIN         46
    #define Z_DIR_PIN          48
    #define Z_ENABLE_PIN       62
    #define Z_MIN_PIN          18
    #define Z_MAX_PIN        43 // 19
//  #define Z_MAX_PIN          -1

#ifndef Z_MIN_PROBE_PIN
  #define Z_MIN_PROBE_PIN  32
#endif
  
    #define Y2_STEP_PIN        36
    #define Y2_DIR_PIN         34
    #define Y2_ENABLE_PIN      30

    #define Z2_STEP_PIN        36
    #define Z2_DIR_PIN         34
    #define Z2_ENABLE_PIN      30

    #define E0_STEP_PIN        26
    #define E0_DIR_PIN         28
    #define E0_ENABLE_PIN      24

    #define E1_STEP_PIN        36
    #define E1_DIR_PIN         34
    #define E1_ENABLE_PIN      30


    #define SDPOWER            -1
    #define SDSS               53
    #define LED_PIN            13

    #define FAN_PIN            9 // (Sprinter config)
    #define FAN2_PIN          -1// 44
    #define V5_COOLING_PIN           44

  #define CONTROLLERFAN_PIN    7
  #ifdef OutageTest
          #define OUTAGETEST_PIN       79
          #define OUTAGECON_PIN        58
  #endif

  #define PS_ON_PIN        -1 // 12 NOT USE

    
   #define  BEEPER_PIN 31
   #define SD_DETECT_PIN 49

  #if defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
    #define KILL_PIN           41
  #else
    #define KILL_PIN           -1
  #endif


    #define HEATER_0_PIN       10   // EXTRUDER 1


    #define HEATER_1_PIN     -1//  45


    #define HEATER_2_PIN       -1

  #define TEMP_0_PIN         13   // ANALOG NUMBERING
  #define TEMP_1_PIN         14   // ANALOG NUMBERING
 
    #define TEMP_2_PIN      -1//   15   // ANALOG NUMBERING



   #define HEATER_BED_PIN    45 //8  // BED

  #define TEMP_BED_PIN       14   // ANALOG NUMBERING

  #ifdef NUM_SERVOS
//    #define SERVO0_PIN         11

    #if NUM_SERVOS > 1
      #define SERVO1_PIN         6
    #endif

    #if NUM_SERVOS > 2
      #define SERVO2_PIN         5
    #endif

    #if NUM_SERVOS > 3
      #define SERVO3_PIN         4
    #endif
  #endif



  #ifdef ULTRA_LCD

    #ifdef NEWPANEL
      #define LCD_PINS_RS 16
      #define LCD_PINS_ENABLE 17
      #define LCD_PINS_D4 23
      #define LCD_PINS_D5 25
      #define LCD_PINS_D6 27
      #define LCD_PINS_D7 29

      #ifdef REPRAP_DISCOUNT_SMART_CONTROLLER
        #define BEEPER_PIN 31

        #define BTN_EN1 -1//33
        #define BTN_EN2 -1//33
        #define BTN_ENC -1//35

        #define SD_DETECT_PIN 49
       
   #elif defined(FULL_GRAPHIC_SMALL_PANEL)
   #define BEEPER_PIN 37
     // Pins for DOGM SPI LCD Support
     #define DOGLCD_A0  23
     #define DOGLCD_CS  27
     #define LCD_PIN_BL 25  // backlight LED on PA3
     
     #define KILL_PIN 41
     // GLCD features
     //#define LCD_CONTRAST 190
     // Uncomment screen orientation
       // #define LCD_SCREEN_ROT_90
       // #define LCD_SCREEN_ROT_180
       // #define LCD_SCREEN_ROT_270
     //The encoder and click button
     #define BTN_EN1 -1//33
     #define BTN_EN2 -1
     #define BTN_ENC 35  //the click switch
     //not connected to a pin
     #define SD_DETECT_PIN 49
       #elif defined(MULTIPANEL)
//         #define BEEPER 37
         // Pins for DOGM SPI LCD Support
         #define DOGLCD_A0  17
         #define DOGLCD_CS  16
         #define LCD_PIN_BL 23  // backlight LED on A11/D65
         #define SDSS   53
         
         #define KILL_PIN 64

         //not connected to a pin
         #define SD_DETECT_PIN 49
       #else
        //arduino pin which triggers an piezzo beeper
        #define BEEPER_PIN 31  // Beeper on AUX-4
/*
        //buttons are directly attached using AUX-2
        #ifdef REPRAPWORLD_KEYPAD
          #define BTN_EN1 64 // encoder
          #define BTN_EN2 59 // encoder
          #define BTN_ENC 63 // enter button
          #define SHIFT_OUT 40 // shift register
          #define SHIFT_CLK 44 // shift register
          #define SHIFT_LD 42 // shift register
        #else
          #define BTN_EN1 37
          #define BTN_EN2 35
          #define BTN_ENC -1  //the click
        #endif

        #ifdef G3D_PANEL
          #define SD_DETECT_PIN 49
        #else
          #define SD_DETECT_PIN -1  // Ramps does not use this port
        #endif
*/
      #endif
    
  #endif //ULTRA_LCD

#endif